Top Virtual Clock With Second Hand

Bjerg Instruments 5 Pack Bulk Clock Parts with Replacement Movement Mechanism and Hands for 14 to 16 inch Clock (Modern)

  • 5 Pack of movements and hands is great for clock makers. Hands are suitable for a 14-16 inch clock diameter, and possibly other sizes. Check hand measurements listed below and decide if it fits your clock design!.
  • Hour Hand: Full length: 4-3/4 inches, Minute Hand: Full length 7-1/2 inches.
  • Second hand: Full length 6-1/2 inches and from center to end 4-1/4 inches.
  • Silent sweep second hand means NO ticking noises. This is a quiet clock mechanism..
  • Quartz clock motor and traditional style hands kits with battery operated movements. Battery not included..
Check Stock

Seiko Wall Clock Quiet Sweep Second Hand Dark Brown Solid Oak Case

  • If your clock has the second hand,slide the switch to "START". The hands starts moving.Then slide the switch to "STOP" when the second hand is at 12 o' clock position.The second hand stops on the spot..
  • Turn the hand setting knob by catching its protrusions with fingers, and set the hour and minutes hand with the desired time. The hand setting knob turns both clockwise and counterclockwise.When turning the hand counter clockwise,turn back the minute hand by more than 45 Minutes from the desired time and then advance it to the correct time..
Check Stock

Quartz Pendulum Clock Movement Mechanism DIY Repair Parts Replacement with 2 Pairs Hands and Pendulum for DIY Clock Repair

  • What you receive: pendulum clock movement set comes with 2 pairs of hands, pendulum, and instructions, the whole set is convenient for you to replace and repair, easy to install.
  • Pendulum clock mechanism: approx. 23 mm/ 9/10 inch in total shaft length, 15.4 mm/ 3/5 inch in thread length.
  • Jump second movement, suitable for 9 - 13 mm (9/ 25 - 1/ 2 inches) thickness clock panel.
  • Hole center to the tip hand size: the hour hands measure approx. 80 mm/ 3.1 inch and 59 mm/ 2.3 inches respectively, minute hands are approx. 110 mm/ 4.3 inches and 86 mm/ 3.4 inches, the second hand is approx. 100 mm/ 3.9 inches, second caps is approx. 7 mm/ 0.28 inches.
  • Please note that as the clock hands material are aluminum, the hands back color are silver, front color as the picture show.
  • Where to use: these clock pendulum movement sets can be applied for cross-stitch, 3-dimensional embroidery, craft clock, frameless draw clock, etc., bring much convenience to you.
  • For DIY: these pendulum clock movements feature simple and elegant design, these replacement parts suit well to different styles of clock frame, nice tools for DIY design, have the clock designed and made by yourself.
Check Stock

Quartz Pendulum Trigger Clock Movement Chime Westminster Melody Mechanism Clock Kit with 3 Pairs of Hands

  • What you get: in our pendulum clock movement set, you will receive 3 pairs of hands, pendulum, trigger clock movement, chime music box, mounting hardware and instructions, meet your different needs and replacement.
  • Pendulum clock movement size: total shaft length is 17 mm/ 0.67 inch, the thread length is 9.7 mm/ 0.38 inches.
  • Jump second movement, which is suitable for 2-6 mm/ 0.08-0.24 inches thickness clock panel.
  • Hole center to the tip hand size: the hour hands measure approx. 70.5 mm/ 2.78 inch, 70 mm/ 2.76 inch and 82 mm/ 3.2 inch, the minute hands measure approx. 101 mm/ 3.98 inch, 92 mm/ 3.6 inch and 117 mm/ 4.6 inch, and 2 second hand are approx. 100 mm/ 3.9 inch, 1 second cap is approx. 7 mm/ 0.28 inch.
  • Melody effect: the chiming pendulum movement plays the Westminster melody on the hour, automatically silences the chimes after 9 o'clock pm until 6 o'clock am.
  • Practical tools for you: these pendulum trigger clock movement replacement parts are practical for you to design and make your own pendulum clock, help you to replace and change a different look.
  • Please notice that the hands are made of aluminum, don't install them with too much pressure or they will be bent.
Check Stock

2 Pair Hands Quartz Clock Movement DIY Wall Clock Movement Mechanism Clock Repair Parts Replacement Shaft Length 1-1/ 5 Inch/ 31 mm Color Set 3

  • Package and install: come with specially designed with blister cardboard box and instructions, convenient to carry.
  • Clock mechanism size: total shaft length is 31 mm (1-1/ 5 inch), thread length is 24.6 mm (24/ 25 inches).
  • Jump second movement, suitable for 16 - 21....
  • Clock hands kit: package includes 2 pieces of minute hands and 2 pieces of hour hands, 1 second hand and 1 second caps, easy for installation.
  • Hole center to the tip hand size: the hour hands are approx. 80 mm/ 3.1 inch and 59 mm/ 2.3 inches respectively, minute hands are approx. 110 mm/ 4.3....
  • Range of use: suitable for repairing, replacing or making a clock.
  • Applicable to cross-stitch, three-dimensional embroidery, craft clock, frameless....
Check Stock

2 Pack Silent Sweep Clock Movement with 4 Pack of Small Hands,Wall Clock DIY Quartz Mechanism Battery Operated Repair Parts Replacement,9/32 Inch Total Shaft Length.

  • Applicable to cross-stitch,three-dimensional embroidery,craft clock,frameless draw clock,etc.INSTRUCTIONS - Included along with the movements..
  • Youngtown manufactures the 12888 series in various models,they have different shaft lengths and shaft diameters.Makesure the existing shaft and threads before ordering and you will get the right replacement..
  • Movement total shaft length is 7 mm ( 9/32 Inch).No thread.suitable for less than 1/16 inch thickness clock dial..
  • Package contents: 2 clock movements,3 Second hand,4 Minute hand,4 Hour hand,2 rubber gaskets,2 Brass washer,2 Second heads and 5 metal hooks,come with the specially designed protect box and instructions..
  • Good DIY clock supply: suitable for repairing, replacing the broken parts of a clock or serving as good handwork material to make a clock by yourself..
Check Stock

Mudder Quartz Clock Movement with Hands to Fit Dials up to 40 cm/ 15.7 Inches in Diameter Shaft Length 1-1/5/ inch/31mm

  • Measurement: hand length: total hour hand length: approx. 172 mm (6.8 inches).
  • Total minute hand length: approx. 207 mm (8.1 inches).
  • Size: total shaft length is 31 mm (1-1/ 5 inch), thread length is 24.6 mm (24/ 25 inch).
  • Jump second movement, suitable for 16 - 21 mm (5/ 8 - 4/ 5....
  • Wide application: they are fit for cross-stitch, three-dimensional embroidery, craft clock, frame-less draw clock, and specially suitable for DIY....
  • Good DIY clock supply: suitable for repairing, replacing the broken parts of a clock or serving as good handwork material to make a clock by yourself.
  • Warm notice: there are some clock parts made of aluminum, please do not install them with too much pressure or they will be bent.
Check Stock

5 Pairs Clock Mechanism Replacement Clock Parts Long Shaft Wall Clock Movement, High Torque Clock Movement Replacement with 5 Different Pairs of Clock Hands DIY Repair Parts Replacement Clock Kit

  • ...ch well to diverse colors, patterns, shapes clock panel and will not stand out, which are great for repairing, replacing or making a clock by yourself.
  • {Wall Clock Mechanism Replacement Kit Size Details}: - The total shaft length is approx. 20 mm/ 0.8 inches, and the thread length is approx. 13 mm/ 0.51 inches.
  • Jump second movement is suitable for 8-10 mm/ 0.31 - 0.43 inches thickness of clock panel (NOTE: The small parts are included, keep away from children under 3 years old).
  • {Clock Movement Kit's Dependability Feature}: - The clock movement kit offers great accurate time and mute feature. They are equipped with sweeping motion, no ticking, provide you with a quiet environment. Low power consumption, provide longer lifespan.
  • {Wide Application Clock Kit}: - The clock mechanism kit is fit for cross-stitch, three-dimensional embroidery, craft clock, frame-less draw clock, creative clock and specially suitable to be applied as DIY quartz wall clock replacement movement parts, also play a decorative effect.
  • {5 Different Styles Clock Hands}: - This replacement clock mechanism kit comes with 5 different pairs of clock hands in different styles and length for your options, perfect for your clock creations and repairs while providing a decorative effect (Note:....
Check Stock

High Torque Quartz Clock Movement Mechanism Replacement Parts with 2 Pairs of Long Spade Hands

  • Package and install: the package includes 2 pieces minute hands and 2 pieces hour hands, and the color includes black and gold, easy for installation.
  • Simple and elegant design, these replacement parts suit well to different styles of clock frame.
  • Clock mechanism size: high torque jump second movement, drive long clock hands (10 mm to 450 mm), total shaft length is 20 mm (0.79 inches), thread length is 11.7 mm (0.46 inches).
  • Jump second movement, suitable for 4 to 8 mm (0.16 to 0.31 inches) thickness clock panel.
  • Size from the center of the hole to the tip: the golden hour hands is approx. 115 mm/ 4.5 inch and the black hour hands is approx. 154 mm/ 6.1 inches respectively, the golden minute hands is approx. 175 mm/ 7 inches and the black hour hands is approx. 208 mm/ 8.2 inches, 2 caps are approx. 7 mm/ 0.28 inches second cap.
  • Wide application: applicable to cross-stitch, three-dimensional embroidery, craft clock, frameless draw clock, etc..
  • Warm notice: when you install this clock movement kit, please keep the hour hand and minute hand parallel, and please check the sizes before purchase, the back of hands color are silver.
Check Stock

Long Shaft Clock Replacement Movement Quartz DIY Wall Clock Movement Mechanism with 2 Pairs of Hands

  • Package and install: come with especially designed with blister cardboard box and instructions, convenient to carry, when you install this clock movement kit, please keep the hour hand and minute hand parallel.
  • Note: there are detailed installation instructions on the back of the product package.
  • Please install carefully according to the installation steps.
  • Size from the center of the hole to the tip: the hour hand is approx. 133 mm/ 5.2 inches and 116 mm/ 4.6 inches long, the minute hand is approx. 175 mm/ 6.9 inches and 160 mm/ 6.3 inches in length.
  • Clock mechanism size: total shaft length is approx. 23 mm/ 0.91 inches, thread length is approx. 14.6 mm/ 0.57 inches.
  • Jump second movement is suitable for 9 - 13 mm (0.35 - 0.51 inches) thickness clock panel.
  • Easy to install: the clock movements kits is easy for installation, simple and elegant design, these replacement parts suit well to different styles of clock frame.
  • Please choose the suitable size bezel to install the hands.
  • Warm notice: as the clock hands material are aluminum, the hands back color are silver, front color as the picture show, and please check the size before buying.
Check Stock

Mudder 24.6 mm/ 1.0 Inches Thread Length Long Spindle Quartz Clock Movement with 2 Hands for Dials up to 21 mm/ 0.8 Inches Thick

  • Movement size: shaft length is 31 mm (1-1/ 5 inch).
  • Jump second movement, suitable for 16 - 21 mm (5/ 8 - 4/ 5 inch) thickness clock panel.
  • Center of hole hand size: hour hand is approx. 82 mm (3.2 inch).
  • Minute hand is approx. 117 mm (4.6 inch).
  • Wide application: you can enable to use it to repair, replace or make a clock.
  • Applicable to cross-stitch, three-dimensional embroidery, craft clock, frameless draw clock, etc..
  • Package: come with mudder specially designed blister cardboard box and instructions, convenient to carry and use.
  • Warm notice: when you install it, please keep the hour hand and minute hand parallel.
Check Stock

PNY GeForce GTX 1060 6GB Graphics Card (VCGGTX10606PB)

  • Base Clock: 1506 MHz / Boost Clock: 1708 MHz.
  • Free U.S. based technical support and backed by a limited lifetime warranty.
  • Experience next-gen gaming with Virtual Reality.
Check Stock