Top Xilinx Usb Jtag Cable - BuyWiseBest.com

Xecuter JR J-R Programmer V2 NAND SPI with 3 Cable Set For 360 Fat/Slim

Xecuter J-R Programmer v2 is an electronic module of SPI dump for NAND, optimized for J-Runner program, but also functional with AutoGG the most famous application for GLITCH RGH..
Allows dumping and fast writing of the NAND..
Also allows to program Glitch chipsets based on Xilinx chipset (glitchip and rev B and rev C).
Allows programming of NAND for 360 FAT and 360 Slim..
Allows you to programm your chip Xilinx (, X360GlitchChip ...) via a USB port with the correct timing file..

. Allows dumping and fast writing of the NAND..
. Allows programming of NAND for 360 FAT and 360 Slim..
. Allows you to programm your chip Xilinx (, X360GlitchChip ...) via a USB port with the correct timing file..
. Xecuter J-R Programmer v2 is an electronic module of SPI dump for NAND, optimized for J-Runner program, but also functional with AutoGG the most famous application for GLITCH RGH..
. Also allows to program Glitch chipsets based on Xilinx chipset (glitchip and rev B and rev C).

Zybo Z7 comes in two APSoC variants: Zybo Z7-10 features Xilinx XC7Z010-1CLG400C. Zybo Z7-20 features the larger Xilinx XC7Z020-1CLG400C. Either....
A feature-rich, ready-to-use embedded software and digital circuit development board with a rich set of multimedia and connectivity peripherals to....
Built around the Xilinx Zynq-7000 AP SoC, with 650MHz dual-core Cortex-A9 processor and DDR3 memory controller with 8 DMA channels.
On board user interfaces include 6 push buttons, 4 slide switches, 5 LEDs, 2 RGB LEDs, and more.
Expansion opportunities with six Pmod connector ports, over 30 FPGA I/O, four Analog capable 0-1.0V differential pairs to XADC, and more.

The st-link / v2 programmer is a circuit debugger and for the stm8 and STM32 microcontroller families.
The unique Wire Interface Module (Swimming) and JTAG / Serial Debugging (SWD) Interfaces are used to communicate with any STM8 or STM32....
STM8 applications use the high-speed USB interface to communicate with St Visual Developing (STVD) or St Visual Program (STVP) software..
STM32 applications use the high-speed USB interface to communicate with atollic, IAR , or Keil in integrated development environments..

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.
The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software..
STM32 applications use the USB full-speed interface to communicate with Atollic, IAR, Keilor TASKING integrated development environments..

4GB 8-bit eMMC on-board flash storage (rev. 3).
Provides lots of expansion interfaces such as Ethernet, USB host and OTG, TF card, serial, JTAG (no connector by default), HDMI D type, Emmc, ADC, I2C, SPI, PWM and LCD.

Pitch: 0.05″ (1.27 mm) Center Spacing for 2.54mm Connectors.
Wire: 40P 28 AWG (7×36) Stranded 300V UL.
Use this flat ribbon cable to build your own custom cables. Applying to digital cameras, digital camcorders, laptops, LCD TVs, LCD monitors, suitable for most Atmel AVR jtag debuggers, in-system programmers, isp download, etc..

Double rows, 8Pin female to 8Pin female header with both end, compatible with 2.54mm spacing pin headers..
Total length is 12" (30cm) with 2.54mm Female to Female 16P 2 x 8 sockets..
Wire Pitch: 0.05" (1.27 mm) Center Spacing.
Ribbon cable saves space and time on circuit interconnecting assemblies. The Conductor ribbon cable separate easily for clean terminations with standard wire connectors, jacks and pins..
6pcs IDC Connector flat Ribbon cable, Applying to digital cameras, digital camcorders, laptops, LCD TVs, LCD monitors, suitable for most Atmel AVR jtag debuggers, in-system programmers, isp download, etc..

Complete new professional design with own robust enclosure and 40pin ZIF socket.
Fully automatic & no manual set-up needed (eliminate all jumpers & DIP-switches).
Fast mode SPI programming & JTAG support wider the application.
True USB data transfer interface with PC/LapTop for newer laptop use as well as portable application.
Working with the adapters further expands the supported devcices list.

Features flexible and insulation wrap wire, tin-plated copper breadboard jumper cable for test jig, jtag or any electronic test uses..
Plastic spool will be provided together for better organizing..
It is mainly used for PCB testing wire or electronic components inside the connection wire..
Suitable for laptop, motherboard, LCD display, breadboard, electronic test and other PCB soldering fly line..
Widely used in household appliances, heating equipment, catering equipment, air conditioning, lighting, electronic equipment, electric products and automobile industry etc..

BRIEF INTRODUCTION: 100M high sampling rate, 16 channels, 10G depth, multi-logic level threshold voltage adjustable. Supports multiple protocol parsers and integrates 2-channel PWM generators. Ideal tools for system development and debugging such as MCU, ARM, FPGA, etc..
POWERFUL SOFTWARE: The supporting software and resources can support Chinese and English, and the Chinese and English software languages can be adjusted. It supports for Windows XP/7/8/10, for Linux, for MAC OS and other operating systems. It is more powerful and better than oscilloscope in digital signal analysis..
BASIC PARAMETERS：Input channels number: 16.
Sampling rate: 100M@3CH, 50M@6CH, 32M@9CH, 16M@16CH.
USB 2.0 interface, Max sampling depth: 10G.
SUPPORTED STANDARD PROTOCOLS: UART/RS232/485, I2C, SPI, CAN, SDID, DMX512, I21/PCM, JTAG, LIN, Manchester, Modbus, 1-Wire, SMBus, UNI/O. USB1.1, NEC Infrared, parallel, PS/2, etc.
FEATURES: Data display in decimal/hexadecimal/2/ASCII format is convenient for observation and analysis. Both sampling data and analytical data can be exported, which is convenient for archiving or other analysis software..