Top 38 Pin Breakout Box
MakerSpot Prototyping Board for Raspberry Pi 2 Pi 3 A+ B+ Pi4 v2.2 Soldered with Female Connectors with Pin Header Set in Extra Long & Short Length
- 348 holes of prototyping area, Full breakout of the 40-pin Pi Header.
- Holes are connected in row and column groups.
- Silkscreen marking for 40-pin Pi Header reference.
- High quality HASL PCB finishing, D0.9mm drill holes and D1.9mm pad size.
- Pin Headers set: 1 x extra long 40-pin (length: 12mm) stacking header, 1 x short 40-pin (length: 6mm) stacking header.
Check StockMakerSpot RPi Raspberry Pi 2 Pi 3 A+ B+ Proto Breadboard PCB Prototyping Board (3 Pack)
- 348 holes of prototyping area, Full breakout of the 40-pin Pi Header.
- Holes are connected in row and column groups.
- Silkscreen marking for 40-pin Pi Header reference.
- High quality HASL PCB finishing, D0.9mm drill holes and D1.9mm pad size.
Check StockRJ45 GPIO Pinout Breakout Board for Raspberry Pi 1A+ 1B+ 2B 3B 3B+ 3A+ 4B Zero-W
- 8 port(2x4) RJ45 8P8C sockets, with the module you can easily connect Raspberry Pi GPIOs and Power supply to peripheral devices through the RJ45 connector. The module support all 40pin Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B Zero, Zero-W..
- Each RJ45 port is connected Power Supply and GND. Each RJ45 can independently choose from the Raspberry Pi 5V / 3.3V, or from blue terminal block, to supply power to external devices. The 4 5 pin of all RJ45 ports are connected to the power supply(VCC, V+), and 7 8 pin connected to GND(0V)..
- RJ45 GPIO connects: Port 1: UART(RXD TXD) GPIO17 GPIO4. Port 2: SPI(SCLK CE0 MISO MOSI). Port 3: GPIO6 GPIO12 GPIO5 CE1. Port 4: GPIO21 GPIO26 GPIO20 GPIO19. Port 5: I2C(SDA, SCL) GPIO18 GPIO27. Port 6: I2C(SDA, SCL) GPIO23 GPIO22. Port 7: I2C(SDA, SCL) GPIO24 GPIO25. Port 8: I2C(SDA, SCL) GPIO13 GPIO16..
- 2x20pin expansion pin header, pin height 10mm/0.39".
- Packing list: 1x RJ45 breakout board, 4x brass standoffs, 8x M2.5x6 screws, 8x pin jumpers. (the item not include Raspberry Pi, RJ45 cable and plug).
Check StockTreedix RPi GPIO Terminal Block Breakout Board Module Expansion Board Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W
- Easy to operate: Use this module to easily extend the Raspberry pi Zero project to the Internet of Things or industrial control applications.
- There is a mark on the breakout board that can clearly identify the pin position, Breakout board is of excellent quality and adopts double-sided gold forming process.
- The module is small in size and does not occupy other space. It is very convenient when making DIY circuits, and the wires can be easily inserted into the terminals.
- Compatible with Raspberry Pi: This GPIO terminal block is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.
- Note: This project needs to be welded and assembled by yourself.
Check StockOBDII OBD2 38 Pin to 16 pin Diagnostic Adapter Connector Cable Compatible with Mercedes Benz
- Type: Compatible with Benz 38 Pin male to 16 Pin OBD2 female.
- Easy installation and durable and waterproof.
- Works on all Mercedes Benz vehicles with a 38 pin female.
- Compatible with Benz 38Pins male connector OBDII 16pins female connector.
- Fit for Benz 38Pin to 16Pin OBD2 OBDII Adapter.
Check StockScrew Terminal Block Breakout Shield Module for Arduino UNO R3
- Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
- Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
- Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
- With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
- NOTE: the item not include Arduino Uno module..
Check StockCZH-LABS Combo Package D sub DB9 DB15 DB25 DB37 Diagnostic Test Breakout Boards.
- CZH-LABS Combo Package D'sub diagnostic test breakout boards, for industry and computer field diagnostic or test..
- Package quantity: DB9 x1pcs, DB15 x1pcs, DB25 x1pcs, DB37 x1pcs..
- Male and Female connectors for each board..
- Clearly labeled with connector pin numbers..
Check StockTreedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino
- Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
- Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
- The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
- There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
- Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check StockGPIO Status LED Terminal Block Breakout Board for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B
- GPIO status LED and power 5V / 3.3V indication..
- GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
- Support for Raspberry Pi A+, 3A+, B+, 2B, 3B, 3B+, 4B.
- Terminal block pitch 3.5mm, wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm..
- Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi module).
Check StockUSB Type-C Breakout Board Serial Basic Breakout Female Connector Type PCB Converter Board (5 PCS)
- Easy to solder:The upgraded USB-C breakthrough board has powerful power,three times the power as much as previous USB. Easy to integrate the USB-C connector into your project without soldering every tiny SMD pad,Easy to solder to the through-board terminals.
- Simple and sturdy construction:The USB-C breakthrough board can be reversible.That can easily solve the general frustrating problem of USB cables.The USB breakthrough board can adds resistance to the original foundation.
- Convert efficiently:The USB Type-C Breakout Board contain VBUS, GND, CC1, CC2, D+ and D- pins,In total of 6 USB-C connector that can be connect 0.1" pitch connector.Worked perfectly, The board can provide up to 1.5A nominal power and up to 3A power.Depending on the upstream equipment.Can definitely be used to convert keyboards to USB-C Detachable.
- Apply for:The USB Type-C board can be used to replace the charging port on the astro a50 headset.PCBs quality and the contacts soldered with ease.Used these to convert an old hardwired keyboard to removable usb-c. Worked perfectly.
- Package content:5pcs High quality USB Type-C Breakout Boards+5pcs pin connector.
Check StockPEIYU Wizard Wand and Witch Magic Wand Cosplay Wand with Steel Core Costume Accessories for Christmas Halloween Birthday Party Favors with Medal and Gift Box
- WHAT’S INSIDE THE PAKAGE: 1pc witch wand, 1pc enamel pin and gift box..
- QUALITY&DURABILITY:This cosplay wand Made out of resin and steel core inside,Non-toxic, tasteless and excellent workmanship, the steel core make sure the wand is not easy to be broke or bent..
- ELEGANT PACKING: Packed in elegant Ollivander Wand Box with plastic textiles in side the box, the wand can be protected and it will not fall out when you open the box..
- PERFECT GIFT&ACCESSORIES: Magic Wand + enamel pin , It will be perfect gifts for Christmas,Halloween and Birthday party & the good accessories for themed costume parties.
- MEASURES&COLOR: 13.38 inches length in black&Silver color..
Check Stock25FT Media Center to Subwoofer Link cable for Select Bose lifestyle 18 28 38 35 48 system 8 Pin Mini DIN to RJ45 interface
- Custom built Media Center to Subwoofer cable for select Bose lifestyle AV18 AV28 AV38 AV48 PS28 PS48 PS38 MC1 etc..
- Works with select Bose lifestyle 18 28 38 35 48 system. Please check compatibility before you buy. Make sure the subwoofer has 8 pin RJ45 interface..
- 25' (25ft) 8-Pin-Mini-DIN to RJ45 cable. Not original Bose part..
- !!!Warning: This is Not 9pin min DIN to 9 pin mini DIN cable! Later version systems require different cable such as 9 pin mini DIN to 9 pin mini DIN....
Check Stock