Top Flux For Copper Pipe

No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance (6 Pieces)

  • ...e size: the rosin flux pen measures about 14.3 cm/ 5.6 inches in length, and the solder braided wick is about 1.5 m/ 59 inches long and 2.5 mm/ 0.1 inches wide, which is convenient to hold in hand.
  • Please check the size carefully before purchasing.
  • Quality material: these no-clean soldering wicks are made of quality copper wire and adopt precise weaving technology, which can enhance tension on the surface to absorb excess solder.
  • The liquid solder pen is made of reliable materials, no leaking and safe for protecting the flux, preventing you from touching the organic solvents.
  • Practical tools: 10-ml solder flux pen with soft brush tip can release the liquid flow moderately, which can clean the components without harming the PCB board copper foil or IC pin.
  • The solder remover wick features good thermal conductivity and absorption, useful to reduce the risk of thermal injury to the circuit boards.
  • Wide applications: these flux pens and braided solder wicks can be applied for laboratory, computer, home repairs and correcting small PCB board errors and through-hole solder joints, electronics welding, etc., bringing a lot of convenience to your work and improving efficiency.
Check Stock

9005 LED Headlight Bulbs, 9006 High Power 9040 Headlamp Replacement HB3 6500K Clear White Conversion Kit, Super Bright 20000lm IP68, HB4 High and Low Beam LED Light Bulbs, Led Lights for Car

  • 【Perfect Beam pattern EMC anti-interference】Built-in high thermal conductivity copper substrate with high power CSP chip, Wireless, 20,000lm per set and 6500K Xenon White. Allowing light to carry wider and further (200 meters) than standard halogens, 600% brighter than halogens, no blinding or glare to on coming drivers, no traffic accidents. effectively illuminate wildlife, debris, and oncoming traffic as well as navigate inclement weather and storms。Light up your life and drive safely..
  • 【Quick Installation Without Struggling】Built with a smaller/ shorter size 1:1 than the common LEDs in the market without building an external driver，keeping you away from all installation hassles, directly plug into the factory housing..
  • 【6pcs New Flip Chip Amplified Flux Beam】600% Brighter than Halogen, provides 4 times as much light as than stock and excellent night time drivability by taking an amplified flux beam with 6 pieces flip chips on each bulb. The aluminum parts are much thinner than the common ones in the market perform with no dark spot.
  • 【IP68, New Cooling System Better Heat Dissipation, Last Longer】A hollow-carved aluminum heat sink+copper heat pipe is incorporated into the design for efficient cooling to make sure lifespan more longe....
Check Stock

S7 200Amp MIG Welder,110V&220V 3 in 1 MIG&ARC&Lift TIG Gas/Gasless Inverter Multi-Process Dual Voltage Welding Machine

  • ️★Multi-Functions In One Machine: IGBT Full 30-200Amp(Max)With Digital Display, Reliable Quality And Stable Performance.Suitable For MMA, Lift TIG, Flux MIG, Gas MIG,Big Enough To Handle 2 To 10 Pound Rolls Of Wire.
  • ️★110V/220V Powerful Machine: Up To 200A Output Current That Can Weld Mild Up To 5/32 Inch (4.0mm) Plate.MAX 5KG Rolls Of Wire.030"(0.8mm) With Solid Core Wire, And .035" (0.9mm)With Flux Core Wire.Can Handle E7018 Basic Electrode.
  • ️★Include:MIG Gun(2.8M), Ground Clamp And Holder (2M),220V To 110V Adapter , Drive Roller Wheel,Contact Tips,Gass Nozzles，Welder Operation Manual . Processes Recommended-MIG-Cast Iron,Copper,Brass,Titanium, Magnesium Alloys. Flux Cored- Aluminium, Cast Iron,Copper,Brass,Titanium.
  • ️★Synergic Control,Automatic Change Of The Voltage & Wire Feeding Speed By Adjusting The Amperage Or Choosing Different Thicknesses.The MIG-200is Capable Of True lift TIG(Need Buy Extra Tig Lift Torch,Not Included Inside Product) Welding As Well As Stick Welding ,The MIG-200 Is An Intuitive Synergically Designed MIG/MAG/ Flux Core/ARC/Lift TIG Welding Machine Safety, Automatic Protection Function For Over-Current, Over-Voltage And Over-Heating.
Check Stock

Bernzomatic PC3 Copper-Phosphorous Brazing/Welding Rods, 3-Piece

  • Copper-phosphorous brazing/welding rods ideal for use in refrigeration, electrical and plumbing jobs.
  • Working temp: 1,310-1,475-Degree farenheit.
  • Joins copper to copper without flux, or copper to copper alloys (brass, and bronze).
Check Stock

30 Pcs 1/2 Inch Brass PEX Fittings with 100 Half Clamp J Hook with Nail Black Pipe Supports PEX Mounting Bracket Coupler Crimp Fittings for PEX Tubing Fitting Connection (Elbow, Tee, Straight)

  • Extensive Usage: these PEX tubing clamps are suitable for copper crimping ring system, plastic or rubber hose, PEX crimping tool and brass crimping accessories, also nice for hot or cold water systems, nice combination to meet your needs in different applications.
  • Easy to Install: this brass PEX fittings kit can be installed without flame, flux or glue, which can help you save time and energy, simple and convenient to use, and can provide a nice using experience for you.
  • Size Details: the crimp PEX fittings are compatible with crimping or cinch type rings and connectors.
  • The adjustable size range of black pipe supports with nail is about 10-14 mm/ 0.39-0.55 inch, please choose the right size before ordering.
  • Solid and Sturdy: these PEX pipe fittings are made of quality brass, safe and stable, solid corrosion resistance, high temperature ductility, waterproof and oilproof, which can be applied for long time.
  • Nice Combination: you will receive 30 pieces of 1/2 inch brass PEX fittings, including 10 elbow, 10 tee and 10 straight coupler crimp fittings, 100 black half clamp j hook with nail, sufficient quantity can easily meet your daily use and replacement needs.
Check Stock

Brass Compression Tube Pipe Fitting Connector, Straight Coupling Adapter,1/4\ Tube OD x 1/4\ NPT Male Connector 5pcs (1/4\ OD Compression x 1/4\ NPT Male)

  • Tube OD Compression to NPT tube adapter for converting Standard National Pipe Thread (NPT) pipe to Aluminum, Plastic, and Copper straight compression thread pipe Tubing..
  • Heavy-duty brass construction with rust proof, corrosion resistance, high temperature ductility and low magnetic permeability.
Check Stock

21 Sticks BLUEFIRE BCuP-2 Half 1/2 lb Self Fluxing Phosphor Copper Brazing Alloy Welding Rods No Need for Flux 0.050 x 1/8 x 14 Industry Professional Grade Propane Gas Soldering Torch Supply

  • Self Fluxing: USA USA AWS A58 Class: BCuP-2 brazing alloys rods. Contents: Phosphor (P): 6.6-7.4%.
  • Copper (Cu): Rest. This brazing alloy is close to eutectic crystal composition. It is self fluxing and do not need any brazing flux when soldering copper to copper or copper to brass joints, while for brazing brass to brass parts, Bluefire JFB-102 brazing flux is recommended for best results..
  • Valued Pack: Each tube contains 21 sticks of 14" long brazing rods, total 0.5 (1/2) pound in weight. GREAT SAVING!.
  • Best Performances: Solidus Temperature: 1310°F / 710°C, Liquidus Temperature: 1508°F / 820°C. Recommended joint clearance: 0.002"/0.007", Fluid Rating: 5. JCuPB brazing rods contain lesser phosphors, resulting a much better plastic performances and a little higher melting points..
  • Versatile: A popular and economic solution for HVAC, Plumbing and Mechanical repairing. Ideal for gas welding, MIG and TIG welding, contact welding, HF brazing and some furnace welding. Perfect for brazing Copper to Copper, or Brass and Bronze joints in A/C, freezer, evaporator, heat exchange, water heater and etc. Cannot be used to weld iron or steel parts..
  • High Quality: All Bluefire brazing alloys are manufactured under highest quality control. Equivalent to HARRIS 0 PN0....
Check Stock

XIFOWE Copper Tube 1/4 OD x 3/16 ID 5 Ft Tube Wall 1/32 Refrigeration Seamless Round Pipe Tubing Soft Coil Copper Tubing Used In Refrigerators Freezers Air conditioners DIY projects Etc

  • 【Size】✔ 1/4" OD - 3/16" ID (6.35-4.75mm) | Tube Wall: 1/32" (0.8 mm) | Length: 5 Feet (1.524M). Note that the actual length of the copper tube is slightly longer than 5FT because it is measured manually. In addition, when we cut the copper pipe, we used a ring cutter, which will deform the section surface, resulting in a smaller inner diameter from the section surface. Please rest assured that this will only affect the size of the section surface, but not the actual size of the copper pipe..
  • 【Material】✔Soft copper pipe copper pipe is made of high quality copper material, the surface is smooth without seam. Note, because it is made of pure copper, so the surface is inevitably easy to oxidation and discoloration, can be polished with high mesh sandpaper, will become bright and clean!.
  • 【Good Thermal Conductivity】: Good heat dissipation and refrigeration capability, high strength at low temperature. This is a good choice for refrigerators, freezers, air conditioners and other refrigeration equipment.
  • 【Shape Changeable】Soft, Because copper pipe can bend and deform, they can often be made into elbows and joints. Smooth bending allows copper tubes to bend at any angle. Or used in manufacture of magnetism instruments or meters..
Check Stock

QLOUNI 80Pcs 7-21mm 304 Stainless Steel Single Ear Stepless Hose Clamps with Clamp Crimper Tool Kit,For Water Pipe, Plumbing, Automotive and Mechanical Application

  • 10T Crimping Power: Fits 1/2"(12.7mm), 3/4"(19.05mm), 1"(25.4mm) copper tubes. Our hydraulic pipe crimping tool features excellent crimping performance, offering 10 Tons compressive force, more labor-saving, and crimping pipes in seconds..
  • Changeable Dies 1/2", 3/4", 1": With ball-bearing springs inside the head, simply slide in and out to change crimping dies of different sizes. This hydraulic copper tube fittings crimper meets your various demand fast for pipe maintenance and repair..
  • Hydraulic System: The hydraulic pipe crimper is constructed of 40CR steel with punching & forging process and powder-coated treatment. It is an integral hydraulic pipe crimping tool with a standard manual hydraulic pump..
  • Easy & Reliable: Thickened and insulated handles give you a comfortable and secure user experience. Fitted with an oil return valve, this hydraulic pipe tube crimping tool will release pressure automatically when reaching the max pressure..
  • Wide Application: The hydraulic copper pipe crimping tool is suitable for copper pipes, copper fittings & joints, copper sleeves. It is widely applied in electric power, traffic, petroleum, chemical engineering, mining, metallurgy, and shipbuilding areas..
Check Stock

BLUEFIRE J9802B 1/4lb Flux Cored Low Temperature Aluminium Brazing Coil All Purpose Welding Coil for Almost All Metals Soldering Propane Torch Universal Welding Rods flux Free

  • ...ods is more convenient to carry than the rod design, you can use the brazing rods coil in your pocket for repair work anywhere and whenever it's needed. A great and thoughtful design!.
  • 【Universal Magic Alloy】BLUEFIRE flux cored welding coil is mainly made of zinc aluminum alloy,which can be used for brazing copper and aluminum, aluminum and aluminum, aluminum and stainless steel, aluminum and steel, etc.More specificly,BLUEFIRE flux cored welding coil can be used for brazing transformer,reactor,condenser, evaporator, radiator,motor, battery or other household appliances.You can use it to complete most of the brazing work in life..
  • 【Easy to Melt and Flow】BLUEFIRE flux cored brazing rods coil can melt at 752°F and have very good fluidity with good capillary attraction.In addition, BLUEFIRE flux cored welding wire is not only corrosion-resistant, but also is post-braze cleaning unnecessary. It's characteristics of high thermal conductivity and high conductivity make the welding effect full and smooth.It fits both professionals and amateurs..
  • 【Moistureproof】BLUEFIRE flux cored welding wire won't absorb water, so it can be stored in various environments for a long time. The special moisture-proof process extends its service life. Even if yo....
Check Stock

Pipe Cutter [1/8\ - 1 1/8\] Tube Cutter Tool for Copper Pipe, Stainless Steel Tubing, Metal, Plastic, Brass - Copper Pipe Cutter - Compact & Tight Space Rigid Tubing Cutter Set for Plumbing

  • HANDYMAN’S BEST FRIEND – Our tubing cutter is especially designed to assist plumbers, electricians & mechanics – whether it’s used as a screw cutter, copper cutter, steel cutter, brake line cutter or an exhaust cutter..
  • PLACE, ADJUST AND ROTATE – Cutting copper tubing has never been easier. Simply, put the tube in the slot where the blade is, adjust to the appropriate setting and rotate your tube. It’s never been this effortless to cut copper tube..
  • NOT JUST FOR COPPER – Our pipe cutting tool isn’t just a great copper tube cutter but also can also cut steel pipe, stainless steel tubing, aluminium piping, PVC and iron. However, we do not recommend cutting PVC pipe as it’s a lot more difficult to cut..
  • GREAT FOR SMALL SPACES – Looking for a fantastic copper pipe cutter for tight spaces? Look no further! Our small pipe cutter fits perfectly in restricted spaces. Our metal tube cutter is also great as an accurate arrow cutter..
  • EXTRA BLADE – Our mini pipe cutter also comes with an extra blade so you can cut as much steel tube as possible. We truly believe our Pipe Cutter is the best in the marketplace and we stand by that. If our tube cutter doesn’t cut it, we’ll FULLY REFUND YOU. So, click "Add to Cart" now and buy with confid....
Check Stock

S7 200Amp MIG Welder,110V&220V 3 in 1 MIG&ARC&Lift TIG Gas/Gasless Inverter Multi-Process Dual Voltage Welding Machine

  • ...th Flux Core Wire.Can Handle E7018 Basic Electrode.
  • ️★Complete Welding Kit: Includes MIG Gun(2.8M), Ground Clamp and Holder (2M), 220V to 110V Adapter, Drive Roller Wheel, Contact Tips, Gass Nozzles, and Welder Operation Manual. Processes recommended for MIG-Cast Iron, Copper, Brass, Titanium, Magnesium Alloys. Flux Cored- Aluminium, Cast Iron, Copper, Brass, Titanium..
  • ️★Intuitive Synergic Design: Synergic Control with automatic change of the voltage & wire feeding speed by adjusting the amperage or choosing different thicknesses. The MIG-200 is capable of true lift TIG (TIG Lift Torch not included) welding as well as stick welding..
  • ️★Safety Features: Automatic protection function for over-current, over-voltage, and over-heating..
Check Stock