Top Gm Diagnosic Tool

KINGBOLEN EL-50448 Plus TPMS Relearn Tool for Ford GM Automotive Tire Pressure Monitor Sensor 315/433 MHz Reset Tool, 2 in 1 Activation Tool for F150/Focus/Lincoln/Buick/Cadillac Vehicle

  • 【Ford & GM Tire Sensor Relearn Tool】The EL-50448 Plus tire pressure monitor sensors 2 in 1 Relearn Tool is perfectly compatible with Ford and GM series cars, including F150, F250, Focus, Lincoln, Mercury, Buick, Cadillac, Chevrolet, GMC, Daewoo, Opel, Isuzu, etc.(Truck is not supported. No support for Toyota and Nissan).
  • 【Easy To Operate】1.Put a new 9v battery into the tool and set the car into TPMS learning model. 2.Start from left-front tire, point antenna against the sidewall of the tire, near the valve stem. 3.Depress the power button, the horn bleeps once then move to the next tire. 4.Follow this order to reset TPMS one by one: front left, front right, rear right, rear left tires. 5.After all sensors reset, the car horns twice means TPMS relearn finished.（9V battery not included）.
  • 【High-quality EL50448 TPMS Relearn Tool】The EL-50448 Plus tire sensors reset tool is portable and convenient, small but high performance, work well on most Ford and GM series cars equipped with 315/433 MHz. With good penetration, the tire pressure sensor can be easily reset and learned..
  • 【Trusted Tire Pressure Activation Tool】Through FCC certification, powerful circuit board and sensitive sensor chip design, our TPMS Relearn Tool EL-50448 Plus can acti....
Check Stock

ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch Puller for Car Auto Air Conditioning on GM, Ford, Chrysler

  • REPLACe A/C CLUTCH ASSEMBLY: Use the ABN Air Compressor Clutch Rebuild Removal Tool Kit – AC Clutch Puller for Car Auto Air Conditioning to remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors.
  • GM R4 and A6, HR-6, DA-6 and V A/C compressors.
  • sander compressors SD 505, 507, 575, 708, and 709.
  • Wide application of vehicles including GM, Ford, Chrysler, imports, and other makes and models.
  • Check vehicle owner’s manual for a list of compatible compressors.
  • EASY TO USE: Keep all threads clean and well-oiled.
  • Outer part of tool has smooth side and threaded side (threads used to attach to inner clutch shaft when removing).
  • Start with one bearing between tool and clutch, and thread down fully onto compressor's inner shaft threads (This is the fixed part - inner bolt does not move when threading down outer piece).
  • Remove tool and stack other bearing on to take up the distance the clutch pushed into pulley.
  • BUILT TO LAST: Constructed from stainless steel with a black coated finish for ultimate strength and longevity.
  • Resists rust and corrosion with proper care and lubrication.
  • 2 and 3 hold puller plate allows mechanical force to do all of the pulling on most clutches.
  • EASY STORAGE: Heavy-duty 10.5” x 8.25” x 2.25” inch (2....
Check Stock

ARES 18010 - Universal Hydraulic Flaring Tool Set - Create 45 Degree Single or Double Flares, ISO and DIN Bubble Flares, Push Connect Flares and GM Fuel Line Flares

  • INCLUDES: This Universal Hydraulic Flaring Tool Set includes one hydraulic flaring tool assembly, and all of the dies and adapters you need to create 45° Single or Double Flares, ISO/DIN Bubble Flares, Push-Connect and GM Fuel Line Flares in the following tubing sizes: 45-degree single or double flares in 3/16, 1/4, 5/16, 3/8, & 1/2-inch.
  • ISO/DIN bubble flares in 4.75, 6, 8 & 10mm.
  • Push-Connect type flares in 1/4, 5/16, 3/8, & 1/2-inch.
  • and GM style fuel line flares in 5/16 and 3/8-inch tubing..
  • DESIGN CONSIDERATIONS: This tool is designed to be used on- or off-car with a hydraulic cylinder, so you can create flares as efficiently as possible when and where you need them..
  • APPLICATIONS: This Universal Hydraulic Flaring Tool can be used to create 45-degree Single or Double Flares, ISO/DIN Bubble Flares, Push Connect-Style Flares and GM Fuel Line Flares in a wide variety of materials including steel and soft metal tubing. Whether you’re working on brake lines, transmission cooler lines, or fuel lines, this tool will help you create the flares you need quickly and easily..
  • RELIABLE | EFFECTIVE | EFFICIENT: Users trust ARES to be quality tools. You are backed by our Performance Assurance. If you have any issues with your ARES Universal Hydraulic Fla....
Check Stock

OTC 6779 Injector Puller for 2005-2011 GM Duramax Engines

  • OTC Injector Puller for GM Duramax engines - similar to Kent Moore J-46594.
  • For use on 2005-2011 model year GM Duramax 6.6L engines.
  • Safely pulls the injectors from the cylinder heads without pulling the injector cups.
  • Simply insert the tool into the injector retainer bracket bolt hole, attach a socket and ratchet/breaker bar to one of the hex ends and start rocking back and forth - the injector will pop right out.
  • Durable steel construction means tool will withstand heavy shop use and continue to perform as designed.
Check Stock

OTC 6778 Injector Puller for 2001-2004 GM Duramax Engines

  • OTC Injector Puller for GM Duramax engines - similar to Kent Moore J-44639.
  • For use on 2001-2004 model year GM Duramax 6.6L engines.
  • Safely pulls the injectors from the cylinder heads without pulling the injector cups.
  • Simply insert the tool into the injector retainer bracket bolt hole, attach a socket and ratchet/breaker bar to one of the hex ends and start rocking back and forth - the injector will pop right out.
  • Durable steel construction means tool will withstand heavy shop use and continue to perform as designed.
Check Stock

AUTOAND GM Harmonic Balancer Remover Puller, Automotive Replacement Engine Harmonic Balancer without Tapped Holes, Crank Pulley Puller Compatible with Ford Coyote 5.0

  • [QUICK & SAFE] GM harmonic balancer puller kit is intended to quickly and safely remove harmonic balancers without tapped holes. This tool features a "clip-in" design allowing removal without bolting the puller to the balancer. The harmonic balancer without threaded holes can also be easily removed..
  • [APPLIACABLE VEHICLE] The harmonic balancer puller tool is compatible with GM models: 5.3L, 5.7 LS1, 6.0 LS2, 6.2 LS3, 7.0 L. Compatible with Chrysler, Jeep, Dodge models: 3.5 L V6, 3.6L V6, 4.7 L V8, 5.7 L V8, 6.1 L V8..
  • [INAPPLICABLE VEHICLES] This tool is not applicable to 1997 or earlier GM LT (5.7L LT1003c4) series engines (with threaded holes), and does not apply to 2018+ Ford 5.0 engines and newer Coyote balancers. Also will not work with the truck pulley. (If you have any issue, please feel free to contact us by email).
  • [EASY TO USE] Lubricate and tighten the pressure screw, after inserting the jaws into the spokes, turn them carefully clockwise to engage the harmonic balancer. Tighten the pressure screw to reach the crankshaft, finally use a wrench or a ratchet to turn the compression screw carefully until the harmonic balancer is removed..
  • [HIGH QUALITY] The harmonic balancer removal tool allows you to complete the work faster and save your time, w....
Check Stock

Geilibuy Tpms relearn Tool gm,Auto Tire Pressure Monitor System Sensor Activation TPMS Reset Tool OEC-T5 for GM/Buick/Chevy/Cadillac Series Vehicles

  • 【TPMS SENSOR ACTIVATION TOOL】:EL-50448 works on GM series products that have TPMS sensors. Please check whether EL-50448 is available for your car.
  • 【GM TPMS Reset Tool】:EL-50448 Orange OEC-T5 can help you reprogram your tire pressure easily within just 3 steps. This TPM relearn reset tool is easy to activate the individual TPM sensor with only pressing one button..
  • 【Easy to Use】Super EL-50448 Tire pressure monitor sensor activation tool is simple, fast and easy to use,activates the individual TPM sensor with the press of one button..
  • 【How to Use】Make sure your car is in the TPMS Learning Mode , Hold the tool against the sidewall of the tire, near the valve stem. Depress learn button while holding the tool against the tire sidewall until horn bleeps once..
  • 【MONEY BACK GUARANTEE】We carry the best car detailing supplies on the market! You will get fast refund service if not satisfied..
Check Stock

OBD2 to OBD1 GM Adapter, OBD1 12 Pins to OBD2 16 Pins Scanner Diagnostic Tool OBD II Adapter Cable Connector for GM (1pc OBD2 to OBD1 GM Adapter)

  • 【Obd1 Scanner】You will get the 1pc obd1 to obd2 adapter, which is a GM 12 pin to OBD2 16Pin connector for car..
  • 【Obd1 to Obd2 Adapter】OBD1 12 Pins to OBD2 16 Pins cable is a fault diagnosis tool cable with high utility for connecting scanners and vehicles..
  • 【Obd2 Scanner】The OBD1 adapter cable is made of high quality metal and plastic materials, which are environmentally friendly and will keep you going for a long time..
  • 【GM 12 Pins Male Connector】OBD1 Adapter Cable Easy To use, 2 Pins To 16 Pins OBD Cable allows you to connect your GM with OBD1 12 pins socket with your existing 16 pins OBD2 tool..
  • 【OBDII 16Pins Female Connector】OBD2 to OBD1 GM Adapter is manufactured in accordance with the original specifications, in line with strict quality control standards, you can rest assured to use..
Check Stock

Goliton 12 Pin OBD1 to 16 Pin OBD2 Diagnostic Scanner Convertor Adapter Cable Compatible for GM Daewoo

  • Connects a 16 pin OBD 2 diagnostic tool to a for GM Daewoo car with 12 pin socket..
  • Works with all for GM Daewoo cars made after 1996 with a 12 pin diagnostic connector..
  • Connector: for GM 12 pin male connector & OBD2 16 pin female connector.
Check Stock

OTC 4202 6-Piece Nozlrater Nozzle-Tester Adapter Set with Metal Storage Box

  • OTC's Nozzle Tester Adapter Set is essential for testing injector nozzles on automotive diesel engines.
  • The set has 6 universal adapters that connect to the number 4200 Nozlrater testing unit - all packed in a handy, metal storage box.
  • Set features the No. 36352 Fuel Line Assembly, No. 23617 90 Degree Adapter, No. 23621 Straight Adapter, No. 23622 Adapter Nut, No. 201917 Adapter Nut,....
  • Set services: Chevy Chevette & GM 1980 and newer C.A.V. nozzles.
  • High-grade materials ensure quality performance over the lifetime of the tool.
Check Stock

VEVOR Hydraulic Flaring Tool Kit 45° Double Flaring Tool Brake Repair Brake Flaring Tools for 3/16 -1/2 Brake Flare Tool with Tube Cutter and Deburrer 32 PCS Tube Flaring Tools for Copper Lines

  • Tube Expanding Functions: This hydraulic flaring tool is equipped with a 45° flaring cone and φ 3/16 - 1/2 inch expanding dies and adapters, including, push connects, GM fuel lines, GM transmission cooling line, 45° and double flares, ISO bubble flares..
  • Manual Hydraulic Mechanism: This hydraulic flare kit achieves the pipe expanding with a hydraulic mechanism. The hydraulic tool is designed with exquisite details, such as a pressure relief valve and no-leakage oil cylinder. You can easily operate this tool without effort..
  • Pipe Cutting & Deburring: The double flaring tool comes with a mini pipe cutter and deburrer, which can help to flare pipe. The cutter cuts tubes ranging from 1/8" -5/8" quickly with a solid and sharp blade. The deburring tool is used for cleaning the interior and exterior of tubing..
  • Durability & Portability: The flaring tool is durable 40 CR steel, which is reliable and built to last. Besides, the flaring tool kit is stored in a plastic toolbox, reducing the possibility of missing parts. It is compact and easy to carry..
  • Wide Application: This hydraulic flaring tool kit is suitable for expanding copper piping. It is an excellent tool for repairs on vehicles or making lines off a vehicle, ideal for the refrigeration and ai....
Check Stock

Arozk TPMS Tire Pressure Monitor Sensor Auto Relearn Reset Activation Tool OEC-T5 for GM Series Vehicle 2006-2022

  • 【2022 For GM TIRE TPMS RELEARN TOOL】Works on most GM (Chevy / Buick / GMC / Opel /Cadillac etc)equipped with 315/433 MHz , Please check the last picture with exact car model. More car models will be updated after being tested!【Please comfirm VXDAS brand LOGO, without LOGO are FAKE, and not sure the quality】.
  • 【ESSENTIAL VEHICLE TOOL】Tire Reset Activate Easily within 1-2 Mins, after tire rotations or change a new tire, Remote Control Door Lock Receiver Module replacement or Tire Pressure Sensor replacement..
  • 【EASY TO USE】tpms reset tool can help you reprogram all tires much easier just with 3 steps. Ensure that the vehicle is in the TPMS Learn Mode, and follow the service procedure. Hold tool against the sidewall of the tire, near the valve stem. Depress Learn button while holding the tool against the tire sidewall..
  • 【SAVE TIME& MONEY】Tire pressure monitor sensor activation tool is simple and fast ,activates the individual TPM sensor with the press of one button easily within 1-2 Mins.Save your almost 20-80$,.Much better than going to the dealer or a tire store just to get your pressure sensors reset..
  • 【FRIENDLY TIPS】: 1.Make sure to hold the battery in place ,or it will not work (if you have a Excessive Installation problem about t....
Check Stock