Top Lathe For Pen Turning

Penn State Industries PKCPMINSS Mini Bolt Action Keychain Pen Kit Starter Package Woodturning Project

  • Keychain/Pen hardware and bushing set only.
  • A LATHE IS NEEDED TO 'TURN' INTO FINISHED KEYCHAIN PENS.
  • Blanks, drill bit, and all other turning tools and supplies are not included.
  • Includes (4) Mini Bolt Action Keychain Pen Woodturning Kits.
  • You will receive (2) of each in Chrome (PKCPMINCH) and Gun Metal (PKCPMINGM).
  • Also includes the bushing set (PKCPMINBU) needed to make the keychain pens.
  • Features a 7mm single tube design, a bolt action mechanism, and a mini ballpoint black refill.
  • Minimum blank size needed to turn is 5/8" x 5/8" x 1-3/4".
  • After turning the blank and assembling the parts, the overall completed product length is 3-3/4".
Check Stock

Accusize Industrial Tools 1/2 x 1/2 x 4 in. (Width by Height by Oal) Hss+5% M35 Cobalt Lathe Tool Bit, 5095-0032

  • M35 Cobalt (HSS + 5%) square lathe tool bits blank, much harder and more durable than M2 high-speed steel lathe tool bits.
  • Ground for heavy-duty cuts on casting and forgings. It has significantly higher wear resistance than M2 HSS。.
  • You may machine it to turning tools to do any lathe turning operations. The possibilities are infinite..
  • Step turning, taper turning, chamfer turning, contour turning, facing, grooving, parting, cut-off, internal threading, outside threading, boring, knurling, etc..
Check Stock

Hurricane Turning Tools, HSS, 3 Piece Bowl Gouge Set (1/4\

  • 【PRODUCTS INCLUDE】 - Lathe tools including(1)10.7"handle (2) 7.9"wood turning tools including square,round,diamond,square arcs(3)easy to replace the head of the T15 wrench,all parts are made of special hard sponge full fitted wrap,in the box..
  • 【5 SECONDS QUICK DISASSEMBLY】 - No tools required,simply loosen the knurled chuck and insert the wood lathe tools,then screw on the collet and you can immediately go to work,the whole process takes five seconds.The wood turning tools for lathe screw self-locking collet fits snugly into the top thread,so you can experience visible robustness..
  • 【HIGH CUTTING EFFICIENCY】 - Sharp high-density tungsten wood lathe cutting edge allows you to handle any wood lightly,and is more durable than other typical carbon and high-speed steel material wood turning tools.It is less likely to deform and stick during cutting,and if the cutting edge becomes dull,simply change the direction of the cutting edge with the included T15 wrench and you will have a fresh,clean cutting edge again..
  • 【EASY TO CONTROL】 - Whether pure aluminum solid handle,or the tool bar of high-speed steel material,mirror polishing treatment to ensure that you can move on the frame without obstacles,square axis wood lathe tools and the tool frame c....
Check Stock

Penn State Industries PKCP7500SS Magnum Bolt Action Ballpoint Pen Kit Starter Package Woodturning Project

  • This is a woodturning project kit. Pen hardware and bushing set only. A LATHE IS NEEDED TO 'TURN' INTO FINISHED PENS. Blanks, drill bit, and all other turning tools and supplies are not included..
  • Includes (3) Magnum Bolt Action Woodturning Project Pen Kits. You will receive (1) of each of the following finishes: Chrome (PKCP7510), Gun Metal (PKCP7520), and Gold (PKCP7500)..
  • Also includes the bushing set (PKCP7000BU) needed to make the pens.
  • Our Magnum Bolt Action Pen kits are 10% longer and wider than our best selling 30 Caliber Bolt Action Pen Kits..
Check Stock

Simple Woodturning Tools Carbide Lathe Turning Tool Set of 3 Full Size with 17 Foam Grip Handles USA Made

  • American Made Set of 3 Full Size Carbide Lathe Turning Tools with Color Coded Handles: Hollower, Detailer & Rougher.
  • 17" long solid aluminum foam grip tool handles are color coded for easy tool identification. Overall tool & handle length is 26.5"..
  • This set of carbide lathe tools is ideal for turners at any skill level. With carbide it's all turning and no sharpening so you can begin turning....
  • Each lathe tool is 1/2" square CNC machined by Harrison Specialties in Ramsey, Minnesota. These tools are designed to be kept flat on the tool rest....
  • Each lathe tool features a carbide tip with multiple sharp edges that can be rotated several times. A Torx star wrench is included..
Check Stock

Penn State Industries PKEXECFREE Executive Pen Kit Starter Package Woodturning Project, Multi

  • A LATHE IS NEEDED TO 'TURN' INTO FINISHED PENS.
  • Blanks, drill bit, and all other turning tools and supplies are not included.
  • Includes (6) Executive Twist Ballpoint Pen Woodturning Kits.
  • You will receive (1) Gold (PKEXEC-PEN), (1) Brushed Satin (PKEXECPENS), (2) Chrome (PKEXECPENC), and (2) Gun Metal (PKEXECPENG).
  • Also includes the bushing set (PKEXEC-BU) needed to make the pens.
  • Features a 3/8" single tube design, a twist mechanism, and a Parker style ballpoint black refill.
  • Minimum blank size needed to turn is 3/4" x 3/4" x 3-1/4".
Check Stock

Accusize Industrial Tools 1\ 9 Pieces/Set, Indexable Carbide Turning Tools and Boring Bar, 2988-0001

  • Package includes: you will receive 4 pieces SCLCR06 lathe boring bar turning tools holders, including a S07K-SCLCR06, a S08K-SCLCR06, a S10K-SCLCR06 and a S12M-SCLCR06, 10 pieces CCMT0602, metal indexable turning insert blades, sufficient quantity and easy to replace.
  • Quality material: lathe boring bar turning tools holder are made of quality cemented carbide and tungsten steel.
  • The cemented carbide material makes the turning tool durable and adaptable.
  • Indexable carbide turning insert blades are made of cemented carbide and use PVD coating, the blade is sturdy, low friction coefficient, wear-proof and stable.
  • Suitable size: the diameter of the S07K/ S08K/ S10K handle is 4.92 inches/ 125 mm, S12M-SCLCR06 is 5.9 inches/ 150 mm.
  • cutting angle is 95 degree, cutting direction is right hand.
  • Each tool holder has a black oxidized smooth surface, and the tool hardness (HRC up and down 48 degrees) and has nice accuracy.
  • Easy to store: insert 10 pieces of cemented carbide into a boxes, and put them in a plastic container, safe and easy to store, compatible with SCLCR06 lathe boring bar turning tools holders.
  • Tight impact bolts, simple structure, often applied for small hole processing.
  • Note: due to the slight color change of manu....
Check Stock

Penn State Industries PKLEVSSX Lever Action Click Ballpoint Pen Kit Starter Package Woodturning Project (With Metal Gunstock)

  • This is a woodturning project kit. Pen hardware and bushing set only. A LATHE IS NEEDED TO 'TURN' INTO FINISHED PENS. Blanks, drill bit, and all other turning tools and supplies are not included..
  • Includes: (4) Lever Action Click Ballpoint Pen Kits With Metal Gunstock and (1) set of bushings.
  • Metal gunstocks are included with this starter package.
  • See Product Description below for more details..
Check Stock

WenCrew Carbide Tipped Wood Turning Tools Set, 2023 Upgrade Carbide Lathe Tools for Woodturning, Lathe Rougher Finisher Swan Neck Hollowing Tools with Extendable Shafts & Full Size Cutters Inserts

  • ... ” can offer better strength and durability to helps maintain edge persistence, to avoid constant sharpening..
  • ▶▶▶ HIGH STABILITY: High performance stainless steel arbor and aluminum oxide handles increase stability and shock resistance. Better shock resistant wood turning tools will ensure the handle will not loosen when vibrating, which will make you get a good cutting effect in safe operation(Heavy duty wood turning tools for lathe are less likely to roll and move on the tool holder than wood tools).
  • ▶▶▶ SIMPLE OPERATEION : Carbide wood turning tools allow both beginner and experienced turners to quickly start projects by reducing the learning curve associated with traditional turning tools. And our wood lathe tools bring you outstanding results, Ideal for lathe woodworking or DIY enthusiasts.
  • ▶▶▶ FAST HANDLE SWITCHING: Excellent reliable ergonomics grip makes you feel comfortable and light. Adjustable and Extendable handle support freely adjust the length according to your preference. Wood turning tools equipped with tools to adjust and extend the length, easy and flexible to assemble and disassemble....
Check Stock

Penn State Industries PKEDCSS DuraClick EDC Click Ballpoint Pen Kit Starter Package Woodturning Project

  • This is a woodturning project kit. Pen hardware and bushing set only. A LATHE IS NEEDED TO 'TURN' INTO FINISHED PENS. Blanks, drill bit, and all other turning tools and supplies are not included..
  • Includes (5) DuraClick EDC Click Ballpoint Pen Woodturning Kits. You will receive (1) of each in 303 Stainless Steel (PKEDCDST), C3604 Brass (PKEDCDBR), 6061-T6 Aluminum (PKEDCDAL), Burnt Bronze Anodized 6061-T6 Aluminum (PKEDCDBB), and Black Anodized 6061-T6 Aluminum (PKEDCDBAL)..
  • Also includes the bushing set (PKSPCL3BU) needed to make the pens.
  • Features an 8mm single tube design, a Schmidt SKM-88 click mechanism, and a Parker style ballpoint refill. Minimum blank size needed to turn is 3/4" x 3/4" x 3"..
  • The pen end includes a tactical designed knurling which is also featured on the pen tip. The pen clip on all finishes is crafted from raw 303 Stainless Steel..
Check Stock

8MILELAKE MT2 Wood Lathe Live Center Set, 4pcs Drive Spur Cup Kit Arbor Woodworking

  • 4pcs MT2 shank Drive Spur Cup live center for woodworking lathe.
  • This MT#2 Lathe Center Set is all you need to start spindle turning on your wood lathe..
  • Made from high quality steel, sturdy and durable..
  • Perfect for both Wood and Metalworking Lathe..
  • The set includes: 1pc 1/8" dia. spur driver, 1pc 5/8" dia. spur center, 1pc 5/8" dia. cupped dead center 1pc liver center for smooth friction free turning.
  • 4pcs white plastic little case for easy storage for each parts.
Check Stock

ASZLBYM 3/8\ Lathe Threading Turning Tool Holder SER1010H11 with Indexable Carbide Threading Turning Insert 11ER A60 (3/8\ Holder + 11ER A60 Insert)

  • PACKAGE INCLUDES : You will receive 1 pieces SER1010H11 3/8”/10mm shank diameter lathe turning tool holder , 11pcs 11ER A60 threading carbide turning inserts and 1pc T8 wrench..
  • Material : The SER1010H11 3/8” metal lathe cutting tool holder material is 40Cr steel, it has the characteristics of durability, sturdiness and stability, and good anti-rust performance. The 11ER A60 threading turning inserts material is carbide, and the coating is Nanostructured TIAIN, It has good toughness, wear resistance and high temperature resistance, the carbide insert can uesd for processing steel..
  • Turning tool holder size : Shank Diameter ( length×width ) : 3/8"*3/8"(10mm*10mm).
  • Threading carbide turning insert :Processing : 60°general thread insert, processing pitch range: 0.5mm - 1.5mm..
  • Easy to store: the metal lathe cutting turning tool holder and threading carbide turning inserts are packed in a plastic container, safe and easy to store, please rest assured to buy!.
Check Stock