Top Module Interface Board

SainSmart Genmtisu GRBL Controller Board for CNC Router Machine 3018-PROVer/ 3018-PROVer Mach3/ 3018-MX3

  • This controller board is compatible with Genmitsu CNC 3018-PROVer. If you have already had the Genmitsu CNC Router 3018-MX3/ 3018-PROVer Mach3, this controller board can help you turn Mach3 control to GRBL control..
  • Applicable Software: Grblcontrol (Candle), LaserGRBL, and other software that supports GRBL firmware, GRBL firmware version V1.1f..
  • USB interface communication, support 3-axis engraving, and laser module..
  • Input interface: X Y Z limit (HOME) interface, Z-axis tool return to zero, emergency stop switch interface, GRBL offline controller interface..
  • All control signals are isolated by optocoupler and have strong Anti-interference ability.
Check Stock

Treedix Mini Pocket AVR Programmer Reset Reprogrammed Module Bootloader BootRescure Compatible with Arduino Controller Board

  • Development board production tool, no other equipment or compiler necessary, Abnormal status recovery bootloader, DIY development board writing bootloader..
  • Used to reprogram the Arduino BootLoader to the microcontroller chip..
  • Easy to program through the ICSP (In-Circuit Serial Programming) interface. Just directly plug it onto the ICSP interface to complete the bootloader..
  • This module can be connected to the ICSP interface, which is the 6 pin headers terminal on the Arduino controller board, which match 5V, MISO, MOSI, SCK, GND and RESET..
  • Compatible with Arduino UNO/UNO Wifi/Nano/Ethernet/Pro/Pro mini/Duemilanove/Diecimila/Mega/Mega 2560/Mega ADK/Leonardo..
Check Stock

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

ACEIRMC 4pcs Si7021 GY-21 SHT21 HTU21 Digital Humidity Temperature Sensor Module Replace SHT11 SHT15

  • The humidity and temperature sensor board that carries a digital SHT21 humidity and temperature sensor from Sensirion..
  • Si7021 GY-21 Module Industrial High Precision Humidity Sensor I2C IIC Interface Module For Arduino Low Power CMOS IC Module.
  • It has a 4-pin interface that can communicate directly with the analog pins.
  • It can be used as a hardware- and software-compatible drop-in upgrade for existing RH/temperature sensors in 3x3 mm DFN-6 packages, featuring precision sensing over a wider range and lower power consumption..
  • The Si7021 offers an accurate, low-power, factory-calibrated digital solution ideal for measuring humidity, dew-point, and temperature, in applications ranging from HVAC/R and asset tracking to industrial and consumer platforms..
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

AOICRIE 5PCS PCF8574T PCF8574 IO Expansion Board Module I2C IO Expander Module (5 PCS)

  • ✔I2C interface, I / O expansion module, two I / O scalability 8 I / O (up to 8 simultaneous use the PCF8574 expanded to 64 I / O).
  • ✔Typical application: I / O resource shortage MCU I / O expansion.
  • ✔Main resources: the PCF8574 I2C interface, 8-bit parallel.
  • ✔Package Included: 5 x PCF8574 IO Expansion Board I/O Expander I2C-Bus Evaluation Development Module.
  • ✔We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution..
Check Stock

8 Pieces Camera Compatible with Raspberry Pi Module with 15 Pin Ribbon Cable and Flex Extension Cable Set Compatible with Raspberry Pi Model A B B+, Pi 2 and Raspberry Pi 3, 3 B+, Pi 4

  • Focus lens: OV5647 Pi camera sensor has a fixed-focus lens, which can capture clear and beautiful images quickly and easily, helping you keep happy moments and save unforgettable memories.
  • CSI interface: 5-megapixel camera module uses a dedicated CSI interface, so the higher bandwidth ink that carries pixel data from the camera back to the processor via the CSI bus, interface carries pixel data from the camera back to the processor, BY THE WAY with pi zero ribbon cable can be applied on zero board perfect.
  • Resolution parameter: 2592 x 1944 Pixel Static Images, 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 video recording,5 megapixel sensor OV5647, and its video resolution is 1080p, which is clear enough for you to use.
  • This is a practical design for you to take some beautiful photos of your family.
  • Flex extension cable set: whatever for 3D printer, home security, or other for raspberry pi camera project, this camera cable set can totally meet your requirement.
  • Compatible with all Raspberry Pi board, camera module and display, suitable for octoprint 3D printing monitoring.
  • Wide compatibility: this 5 megapixels camera module is compatible with raspberry pi model A or B, B+, model 2, raspberry pi 3, 3 B+, pi 4, works well with your equipment, bring y....
Check Stock

DORHEA 5PCS ESP32 Development Board Type-C USB WiFi + Bluetooth ESP-WROOM-32 2.4GHz Dual Core WiFi NodeMCU Processor ESP32-DevKitC-32

  • Dual core ESP-32 development board, 2.4GHz dual mode development board. There are two touch buttons, one is reset, the other is enable module to enter the halberd program mode..
  • The module is ESP-WROOM-32 module, the peripheral uses the USB serial port to expand the type c interface, which can be directly debugged by a USB connected computer, and the data transmission is fast and stable..
  • The module supports for NodeMCU and other development environments, which expands the range of its resources available and greatly improves the ease of learning and development. Of course, it can also be widely used in Internet of things occasions, such as home automation, wireless industrial control, wireless positioning system signal.
  • ESP32 development board support lua program, easy to develop, support LWIP protocol, Freertos, three modes : AP, STA and AP + STA..
  • ESP32 is a safe, reliable, and scalable to a variety of applications,the user can cut off the power of the CPU and use the low-power coprocessor to continuously monitor the status of the peripherals or whether some of the analog values exceed the threshold..
Check Stock

SainSmart XBee USB Adapter for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot

  • This camera module is designed for NVIDIA Jetson Nano Board and Raspberry PI CM3..
  • With 8-megapixel IMX219 sensor and features the fixed focus77-degree field of view. (The drive board is no longer needed.).
  • Support 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 video recording. With the power interface, it also supports 3.3V output power supply..
  • This camera module is widely used for AI intelligent recognition, face recognition, road identification line recognition, license plate recognition,....
  • If you have any questions about the product, please feel free to contact us..
Check Stock