Top Motor Ac Current

UEi DL599 - Wireless TRMS Clamp Meter with Motor Testing (600 A AC/DC)

CR Magnetics CR4411-5 Average RMS AC Current Transducer with Single Element, 20 Hz - 4 KHz, 003e= 2K Output Load, 24 VDC +/-10%, 0-5 AAC Input Range, 0 - 10 VDC Output Range

• CURRENT MONITORING --- Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output..
• STRAIGHT-THROUGH DESIGN --- Straight-through structure design, isolation withstand voltage up to 2000V. Straight-through wire diameter: 0.35-20mm..
• MEASURE CURRENT RANGE --- Self-powered, no external power supply required. Measured current AC 0-100/150/200A, output signal DC 0-10V..
• WIDE APPLICATION --- Suitable for AC current measurement and monitoring, AC motor overload protection, electronic switch of automatic control system and so on..
• ABS OUTER CASTING --- Hysteresis is less than 1% and can be used under strong magnetic conditions. The outer casing is made of self-extinguishing material ABS..

MEISHILE DC 12V 50A 600W Switch Power Supply 110V AC to DC 12 Volt 50 Amp SMPS Converter Power Supply Adapter Transformer

• ☆ Simultaneous power supplies for devices with different currents/watts. Transformer (PSU) convert AC to DC using SMPS mode. Used for DC 12V Servos, Pumps, Car stereos, LED light strip, CCTV security camera, household appliances, electronic devices, brushless motor, automation equipment, computer project, etc.
• ☆ Universal input voltage: AC 110V / 220V (85-145V/185-265V).
• Output current depends on the current drawn by your device. The total output current/power can not exceed 80% of the rated power of the power supply.
• ☆ Portable, Small and Compact: 21.5×11.5×5cm/8.5×4.5×2 inch, Net weight 0.8 kg. SATISFACTION GUARANTEE: For any question, do not hesitate to contact us, we offer you a satisfaction guaranteed.
• ☆ High EFC, Low-loss, Long Service Life: More than 6,000 hours of service life.
•  Low standby power consumption, High efficiency. EFC much higher than linear supply. Safe and Stable: Power Supply has over / under voltage, over heat protection, continuous fan heat dissipation. Strictly tested before leaving the factory..
• ☆ Choose: The Rated Power is the Peak Power, does not mean that it applies to devices at this power (watt). For resistive device, SMPS peak p....

PRINCE CASTLE Drive Motor Assembly 87-028AS

• ATO 110v vfd, single phase 110v/120v input, single phase or three phase 220v output, achieve to run 220v AC motor on single phase 110v/120v power supply.
• 【Voltage& Frequency】Input voltage: 1 phase 120V AC ±15%, Input frequency: 50Hz/60Hz,Output voltage: 1 phase or 3 phase 220V AC ±15%, Output frequency: 0.00~400.00Hz.
• 【APPLICATION】ATO 7.5 hp 5.5kW variable frequency drive Can be widely applied to drive the AC motor, such as fans, pumps, power tools, etc.
• 【TIPS】 To protect the variable frequency drive and Motor, you need an upstream protection, add a line-choke upstream the VFD, this will reduce the current transients seen by the input of the VFD.
• 【CUSTOMER FIRST】If you have no experience in driving a VFD, be sure to refer to the instructions before operating a VFD.If you are not sure about the size or have any issue about the product or service, please don't hesitate to email us. We will answer you within 12h.

SIEMENS 6ES7 214-1AG40-0xB0 SIMATIC S7-1200 CPU 1214C, Compact CPU

• Programmable Control -- This module is programmable control, can achieve thousands of functions, stable and reliable working performance, built-in watchdog timer circuit, to ensure that the module for a long time to run Input high speed pulse C235, C251 and FX1N compatible.Output relay 1A output, Rated current 5A, can directly drive DC solenoid valve, AC solenoid valve, AC contactor, AC motor, etc..
• Built-in Analog Input and Output -- Built-in Analog input AD, corresponding to internal data register D5030.(Not D8030) Built-in Analog output DA, corresponding to internal data register D5101..
• The PLC with Two Programming Port -- The TTL interface and the 232 interface. The 232 interface, you can directly use the USB-232 serial port with a computer to download the program directly. When the PLC need to connect with the touch screen or text, can be used to conne....

New Genuine PS for HP Z420 Workstation 600W Power Supply 632911-001 623193-001

• 24V Power Supply: Input AC 110V/220V, Output 24V, Rated power 24A 600W, PSU(SMPS) AC to DC convert , output current depends on the requirements of the power consuming equipment, Power multiple devices with different Currents/ Watts.
• Intelligent Cooling: 24V 600W Power Supply converter with aluminum alloy shell, built-in cooling fan, metal shell with multiple holes for more efficient cooling, more stable work, high efficiency.
• USED WIDELY：DC 24V Power converter Used for Brushless type motor drive, Amplifier,Radios,LED drive, CCTV Camera System, Car Stereos, water Pump and more 24V Device. NOTE:Not suitable for charging Battery,Speed Control Motors..
• Safe stable: long service life, power supply with over/under voltage, overheating protection,Compact:21.5×11.5×5cm/8.5×4.5×2 inch, weight 0.75 kg，SAFETY: Use must derating: max load cannot exceed 80%.
• Note: SMPS peak power is 25A 600W, avoid overload, For resistive equipment, Recommended for equipment under 20A 480W. For motor equipment, the starting current will be much higher than the rated power and the peak power of the SMPS needs to exceed 2 times the motor power..

Xantrex 817-3000 Inverter, Freedom X, 3000W 12V True-Sine

• Hardwire or plug directly into the optional 20A GFCI receptacle.
• View AC & battery current, % status bar for inverter output on the onboard display.
• Extended Surge Rating: Surges to 2X continuous power for 2 seconds for motor loads.
• True Sine Wave AC Power: For operation of sensitive and motor loads.
• Ignition Control: Feature to turn inverter on/off via a 12 VDC signal and to minimize battery drain by switching the inverter off when the ignition key is turned off.
• Wide 10-18 VDC Input Range: Ensures inverter operation on high voltage alternators found on many new vehicle chassis.
• Built-in 30A AC Transfer Relay: Senses when outside AC Power is present and transfers the load from the inverter to the source of incoming power (shore or generator)..

CHANS TYC-40 Electric Synchronous Motor DC 12V 5RPM Shaft 35mm With Power Supply Input 100V-240V Output DC 12V For Ornamental Fiber Optic Christmas Tree

• 【Description:】It's a combination of an DC 12V motor and a input AC 100V-240V and output DC 12V power supply. Easy to install and easy to operate.....
• 【TYC-40 DC 12V Synchronous Motor Parameter:】 Voltage: 12V DC； Speed: 5r/min ； Shaft Length: 35mm； Shaft Screw Thread Inner Diameter:....
• 【DC Power Supply Parameter:】 Input: AC 100-240V； Output: DC 12V ； Output current: 1500mA； Frequency: 60Hz； Power: 15W； Wire Length:....
• 【Attention:】 1.The power adapter is an DC power supply,NOT suitable for AC motor. 2.Too high voltage will burn the motor and power supply.....
• 【Package Include: 】 1*TYC-40 12V DC 5RPM 35mm Synchronous motor； 1*DC Power Supply； 1*Module.

4000W Motor Speed Controller, Motor Control Board AC 110V Adjustable Voltage Regulator SCR High Power Dimmer Controller Temperature Governor Dimming Monitor

• Note: This product is AC input, AC output, can only step down, and the voltage can be adjusted only when the load is connected. It is useless to connect a multimeter with no load, because it is not a transformer..
• Motor speed controller operating voltage range is AC 110V to 220V, max power is 4000W, long term operating power is 3000W, and adopting double insulation, meaning there will be no electric leakage if short-circuit or SCR burn out..
• Protection: our motor regulator is designed with Anti-spike and anti-surge protection, RC absorption, fuse all enhance usage safety..
• Aluminum Case: the motor speed controller is equipped with Aluminum case prevents it from easy damagement.
• filled tin stops it from heating when in huge current..
• Application: the motor governor can be applied to electric stove, water heater heat regulation, dimming lamp, small motor speed control, electric iron thermostat, etc..

Slim DIN Rail Mount AC/DC Current Sensor Module, Based on ACS712. (+/-20Amp)

• The item disign based on ACS712 IC. The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection..
• Operating Voltage: Regulated 5VDC. Operating Current: 20mA(max). Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Output voltage proportional to AC or DC currents. LED indicator for power supply +5V. Pin jumper option for signal output capacitor..

KAIWEETS HT208D Inrush Clamp Meter 1000A True RMS AC/DC Current Amp Meter VFD LOZ Mode 6000 Counts Measures Current Voltage Temperature Capacitance Resistance Diodes Continuity Duty-Cycle

• True-RMS Clamp Meter: This multimeter can accurately measure 1000 Amp AC/DC Current, 1000V AC/DC Voltage, Frequency, Duty Cycle, Resistance, Capacitance, Diode, Continuity, and Temperature. Easy to use for labs factories and households..
• Inrush Current Meter: Knowing the value of inrush current can help you locate a startup problem quickly, whether it's in the motor or in the starting circuit. The measuring time of the inrush current is about 100ms. When the current is greater than 10A, the Inrush function works well. The inrush function is only available in AC current mode, DC current does not have the inrush function..
• NCV Detection & LED Flashlight: Built-in Non-Contact Voltage (NCV) Detector can easily and quickly determine whether there is a voltage. A convenient LED flashlight illuminates a dimly lit area..
• Advanced Functions: The Clamp Meter has Variable Frequency Drive Filtering (VFD) and low Input Impedance (LoZ) modes, which can provide higher accuracy readings..
• Safety Service: Safety standard IEC 61010-1, CAT IV 600V, CAT III 1000V. Double insulation. Use high-quality material, to prevent electric shock harm. 36-Month product service provided. 7/24 Customer Service..

3 Axis Stepper Motor CNC Router Kit Nema23 425oz-in 112mm Dual Shaft+CW5045 Driver 4.5A 256 microstep+400W 36V Power Supply CNC Controller Kit for Engraving Lathe Plasma Milling Drilling Machine

• ♞【Product】3 Axis nema23 stepper motor driver controller kit.
• ♞【Application】This cnc kit are widely used in engraving machine, printer,....
• ♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
• ♞【Driver】CW5045 driver Voltage: DC 24-50V.
• Current: rated maximum output reaches: ±4.5A.
• ♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
• ♞【Power supply】400W,36V/9.7A switching power supply.