Top Motor Power Controller

EBIKELING Waterproof Ebike Conversion Kit for Electric Bike 26" Front or Rear Wheel Electric Bicycle Hub Motor Kit, 500W, Rear/LCD/Thumb

  • ... BLDC Scooter Motor: Brushless High Speed Mid Drive Motor, Voltage 72V DC, Rated Power 3000W peak, Current 45A, Rated Speed 4900rpm/min, (Max 5800RPM), T8F 11Teeth Sprocket, Load Weight: About 100-200kg. NOTE: motor speed according to your load-weight and others..
  • BLDC Controller: Voltage 48-72V, Proctect 42 volt, Power 3000 watt, 24 mosfet, Current 50 amp, Phase Degree: 120°, Smart Controller Can Work With Hall Sensor And Without hall, Brushless Motor Speed Controller, E-Brake, 3-Speed (Low Mid High Speed), Reverse Functions, Indicator Light And Power Lock Functions..
  • Handlebar Twist Throttle: Universal Accelerator Handlebar Throttle Twist Grips, 12V-72V Universal, With 3 Speed (High,Mid and Low Speed) And Reverse Functions, Wire Length About 150cm ( 59 inch) , High Quality Rubber And ABS Material..
  • Useful: Suit For Electric Scooter, Mini Electric Motorcycle DIY Engine Kit, Razor Push Scooter, Ebike Bicycle, Go Karts, E-bike, E-Tricycle,Mid Drive Motor Kit, Complete Set, DIY Engine System, Cycling Part and more. Packing List: 1pc Motor, 1pc Controller, 1pair Handlebar, 1pc Foot Pedal Throttle 1pc lock key, 1set T8F ch....
Check Stock

Speed Controller AC 50-220V 2000W 25A Motor Controller SCR High-power Electronic Voltage Regulator Module Motor LED Dimmers (1PCS)

  • The output voltage is adjusted anywhere between 50V-220V for use with electrical appliances.
  • It can use to such as electric stove, water heater tune thermal, lighting dimmer, small motor speed, electric iron thermostat, and achieve dimming, thermostats, pressure regulator effect..
  • The motor speed controller can easily provide a continuous current to your DC motor or other DC load..
  • Universal DC Motor Speed Controller.Control the speed of a DC motor with this controller..
  • Before you attempting to wire the controller, make sure all power is disconnected. Cut any one of the battle line or zero line of the lamp or electrical appliances, and connect wires refer to the "wiring diagram".
  • Turn on the power, and adjust the potentiometer..
Check Stock

Tilta Nucleus-Nano Wireless Lens/Focus Control System to Wirelessly Control The Focus of Most DSLR, Mirrorless, or Cine-Style Lenses on Cage, Gimbal Such As Ronin S

  • The Nano Motor allows for automatic calibration of the lens as well as a manual calibration if you are using lenses that don’t have hard end stops at close focus and infinity via the ability to set A-B limits on the Nano Hand Wheel Controller. Every motor has a 0.8 mod, which is the standard gear size for most cinema lenses. The torque of the Nucleus-Nano Motor at 5.5V is 0.65Nm and at 14.8V is 1Nm..
  • The motor has a 5-18V input tolerance for power via a Micro USB port. This allows the motor’s power to be drawn from the G2X tilt motor’s 5V Micro USB output or via a P-tap to 5V Micro USB cable (sold separately)..
  • The Nucleus-Nano uses a brand new state of the art power-efficient miniature motor. The Nano Motor features low noise and high torque. It can perform super fast focus pulls with silent precision! The built-in 15mm rod adapter allows for flexibility and compatibility with a wide range of camera rigs and professional mounting solutions..
  • The Nano Motor has its own built-in motor drive that communicates directly with the Nano Hand Wheel Controller. This negates the need to mount a separate MDR to your rig, allowing for a more compact camera setup and a quicker setup time. Simply set the Nano Motor and Nano Hand Wheel Controller to the same cha....
Check Stock

DORHEA PWM DC Motor Speed Controller DC 10-55V 24V 36V 48V 60A Stepless Motor Speed Controller with Adjustable Potentiometer Forward-Brake-Reverse Switch and LED Digital Display DC Brush Motor

  • Motor speed controller input supply voltage: DC 10V-55V.
  • The motor speed controller is an aluminum case, very strong to prevent damage, holes on its side and top which are helpful for heat dissipation..
  • The pmw dc motor speed controller come with switch function. High power speed controller switch which is much more adaptable and conveniently change the motor direction..
  • The stepless motor knob adjusts the motor speed from 0% ~ 100% smoothly with LED display is accurate to show 0 ~ 100% of the motor speed..
  • The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt, the dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric vehicles..
Check Stock

Kunray 48V Go Kart Motor Kit 1000W Electric Brushless DC Motor Kits 3500RPM with 30A BLDC Mid Motor Speed Controller Handlebar Twist Grip Throttle (48V1000W Kits with Mounting Bracket)

  • ...gh Torque High speed, BLDC Mid Drive Motor with T8F 11Teeth Sprocket, and the Scooter Motor with Mounting Bracket is more easy to Install and Enough Carry, with wind cold hole, Motor Wiring length about 150cm(59inch)，Motor Weight about 3.7kg (8.16lb)..
  • 【Brushless Speed Controller】- 12Mosfet 30A BLDC Motor Control, The Motor Kit include BLDC Motor Controller with high Quality Material, is enough for the Motor, with Hall 3-Speed Reverse Throttle Charging e-Braking Power lock Light Functions etc..
  • 【DC MOTOR KITS POSITIVE & NEGATIVE ROTATION】- BLDC Go kart Motor Can Through the Motor Reversing Wire or Handlebar reverse Switch To Let The Motor Go Clockwise or Counterclockwise, And with 3 Speed Function, Low speed 50%, Mid speed 70-80%,High Speed 100% Efficiency, But Don’t let the Motor Run Reverse Long Time, is Not safe for Motor Life..
  • 【E-scooter Motor Kit Lists & Useful】- 48V 1000W BLDC Motor, Speed Controller, Handlebar Twist Grip Throttle, Foot Throttle, Power lock key, T8F Tooth Plate Ring, T8F Chain, 3 speed Switch, is Good for Electric Scooter, E-bike, Mini Motorcycle,Dirt bike, Electric Go karts, ....
Check Stock

AmpFlow E30-150 Brushed Electric Motor, 12V, 24V or 36 VDC, 5600 RPM

  • Fundamental Parameters: This brushless go kart motor is powerful and efficient. Input Voltage: 48V DC, Output Power: 1800W, Rated Current: 33A, Rated Speed: 4500 RPM, Maximum Speed: 5200 RPM, Sprocket: T8F-9T, Maximum Current: 37.5A. Package includes: 1 x Brushless DC Motor, 1 x Speed Controller,1 x Throttle Grip, 1 x Screw Set, 2 x Wrench..
  • 1800W Brushless Motor: The dc electric go kart brushless motor adopts a 100% copper core for low noise operation and excellent speed regulating performance. The high-precision rotor features high-tech components, a clean finish for water resistance, and high working efficiency. Get ready to leave the competition in the dust..
  • Sturdy Aluminum Construction: The electric brushless dc motor kit features an aluminum alloy shell that resists heat, cold, and deformation, ensuring it will not rust easily. This dc electric motor is a forward and backward rotation motor so that you can switch rotation gears effortlessly..
  • Speed Controller Included: This dc electric motor brushless comes with a controller to provide speed control at a desirable range, speed adjustment method: Potentiometer. Model: BY15WF01-A, Current: 33A, Phase Degree: 120°, Conversion Efficiency: 90%, Under Voltage Protection Voltage: 41±0.5V..
Check Stock

BLDC 72V 3000W Brushless Motor Kit with 24 Mosfet 50A Controller and Throttle for Electric Scooter E Bike Engine Motorcycle DIY Part Conversion Kit (6 Part in 1 and Motor with Foot)

  • Kunray MY1020 Brushless Motor Features: Electric Brushless DC Motor, Aluminum Body, Full Copper Coil, Heat Resistant, Naturally Air Cooled, Low Noise High Quality More Long Life..
  • Motor Type: Brushless DC High Speed Motor, Mid Drive, Voltage 72VDC, Rated Power 3000W Max, Current 45A, Rated Speed 4900rpm/min, Max 5800RPM, T8F 11Teeth Sprocket Chainwheel,Load Weight:100-200kg About..
  • BLDC Controller: Voltage 48-72V, Proctect Vol 42V, Power 3000W, 24 Mosfet, Current 50A, Phase Degree: 120°, Smart Controller Can Work With Hall Sensor And Without Hall Motor, Brushless Motor Speed Controller, E-Brake, 3-Speed (Low Mid High Speed）, Reverse Functions, Indicator Light And Power Lock Functions..
  • Handlebar Twist Throttle: Universal Accelerator Handlebar Throttle Twist Grips, 12V-72V Universal, With Accelerator, 3 Speed (High Speed Mid Speed Low Speed) And Reverse Functions, Wire Length ABout 59inch, High Quality Rubber And ABS Material..
  • Suit For: Electric Scooter, Mini Electric Motorcycle DIY Engine Kit, Razor Push Scooter, Ebike Bicycle, Go Karts, E-bike, E Tricycle,Mid Drive Motor Kit, Complete Set,DIY Engine System, Cycling Part,And More. What You Get: 1pcs Motor, 1pcs Controler, 1pair Throttle, And Manual..
Check Stock

Ezweiji Bike Brushless Motor Controller,48V 64V 350/450/500/1500W 6 Tube Dual Mode for Electric Bicycle Scooter Speed Intelligent Dual Motor Part (500W)

  • 【BRUSHLESS MOTOR CONTROLLER】Electric skateboard 6-tube-dual-mode controller is suitable for voltages Suitable for motors with 350/450/500/1500W power, silent design, durable wires and interfaces, ensuring low failure rate for long-term use..
  • 【DUAL-MODE CONTROL DESIGN】This motor controller adopts a dual-mode control design, which has the advantages of stable starting, comfortable riding, strong climbing power, low noise in use, and intelligent identification and self-learning. It can drive sine wave motors, square wave motors, and Hallless motors, etc..
  • 【SAFETY OF USE】When the electric door lock is turned off, the controller will automatically turn off the power. It can reduce the phenomenon of misoperation and greatly improve the safety performance. When the controller's own temperature exceeds a certain temperature, it will automatically reduce the output current and have the highest temperature protection..
  • 【EASY INSTALLATION】The brushless motor controller has multiple wires with different colors and different functions, which can be connected with only the required functions, and the unnecessary func....
Check Stock

Motor Controller, 60V 72V Universal 3 Mode High Power Brushless Motor Controller for E Bike Electric Bike Scooter

  • ?HIGH QUALITY MATERIAL?The aluminum shell for motor controller with groove design ensures good heat dissipation and high temperature resistance ability,which provides better protection for inner circuit.Full cast aluminum shell, strong heat dissipation, dustproof and waterproof, high stability..
  • ?CONVENIENT TO SWIFT?The controller allows steady and sensitive speed control of braking and direction changes.Superior controller, it has high efficiency, low power consumption and long service life..
  • ?KEEP LONG SERVICE TIME?The wires and interfaces for the controller have good contact, and ensure low malfunction for long time use.Simple and clear wiring harness connection, which has more beautiful appearance..
  • ?BEST ACCESSORY?The motor controller is a perfect accessory for electric bike,and scooter,bringing you a more comfortable riding experience.60V 72V universal, and it can support two voltages at the same time..
  • ?WIDE RANGE OF APPLICATIONS?The brushless controller is applicable to high power vehicles, such as two wheel electric motorcycles, three wheel electrocar etc.Controller Box Size: Approx. 18 x 10 x 4cm/7.1 x 3.9 x 1.6in,Application: 60V 72V universal,Power: 1000W..
Check Stock

RioRand 400W 6-60V PWM DC Brushless Electric Motor Speed Controller with Hall

  • 1.Humanized design,the interface adopts binding posts,standard heat sink,integrated speed regulating potentiometer on the board,it can be used when the power is on,save time and effort..
  • 2.Full patch technology,stable performance,with forward and reverse, brake function.Electric Motor Speed Controller Brushless Controller with Hall..
  • 3.Wide voltage 6-60V high power 400W DC three-phase brushless with Hall controller..
  • 4.High-power 400W DC three-phase brushless with Hall controller, support PLC 0-5V analog control, support PWM control, amplitude 2.5-5V.
  • 5.There are three relatively thick phase wires on the motor, and there are also three phase wire interfaces on the driver board. They are marked with the characters of MA, MB, MC and other similar characters, and they are also connected respectively..
Check Stock

Adjustable Digital display 10-55V 60A PWM DC Brushed Motor Speed Controller Switch Control 12V 24V 36V 48V Forward Brake Reverse For power wheels regulation (60A PWM)

  • The input voltage must be equal to the rated voltage of the motor.Wide Voltage: Wide voltage input 10-55V, maximum output current 60A,Continuous current: 40A..
  • Digital display :Motor Rotation Speed Percentage 0~100% ,Accurate adjustment speed.Adjust Output Current Control Motor Speed.
  • Speed Control Knob:Stepless speed regulation ,and with Forward-Brake-Reverse Switch.Only Work for Brushed Motor..
  • Notice 1: The power of the input power supply must be greater than 1.5 times the rated power of the motor to make the motor work (note: the input voltage and the rated voltage of the motor must be consistent)..
  • Notice: If there is a forward-reverse circuit regulator on the children's car, please be sure to connect the speed controller between the power supply and the forward -reverse circuit regulator of the children's car. Otherwise, the speed controller may be damaged..
Check Stock

CHANCS Mini Electric Motor 775 DC 12V/24V With Drill Chuck and PWM DC Motor Speed Controller

  • This is a DIY combination of motor, bracket, B10 drill chuck，and 20A PWM speed controller, it can be used with a saw blade to become a mini saw..
  • 【The specification of motor:】 Rated Voltage: DC 12V, Unloaded Speed: 10000RPM, Load Speed: 8800RPM. Rated Voltage: DC 24V, Unloaded Speed: 20000RPM, Load Speed: 17600RPM. Starting current: 4-5A Motor Body Diameter: 42mm, Motor Body Length: 66.5mm, Shaft Length: 16mm, Shaft Diameter: 5mm..
  • 【The specification of bracket:】 Length: 50mm, Width: 52mm, Height: 53mm, Mounting hole diameter: 4mm, Thickness of bracket: 3mm..
  • 【The specification of the speed controller:】 Input Voltage: DC 10V-DC 60V (Ultra wide working voltage)； Output voltage: linear under load； Control Power: 0.01-1200W； Rated Current: 10A； Max Current: 20A (Long-term use of 10A, 450W or less, pay attention to keep the module free of heat dissipation conditions.)； PWM Duty Cycle: 0%-100%； PWM Frequency: 25Khz； Product Size(L x W x H): 77*45*28mm；.
  • 【Attention:】 1.About the PWM, please do not connect AC power directly(Such as:110V AC),the input volt of this controller should be DC 9V-60V,otherwise it will be burned out. 2.Make sure the positive and negative connections are correct before powering on the motor speed contro....
Check Stock