Top Oil Control Valve

6.0 High Pressure Oil Pump IPR Valve Air Test Fitting Tool, High Pressure Oil Rail Adapters Leak Test Kit and 6.0 IPR Valve Socket with Seal Kit Fit for Ford 6.0L Powerstroke Diesel Engine

  • ...h Quality Machined from Brass or Steel with excellent mechanical and physical properties, these tool kit show their high tightness, corrosion resistance and durability.
  • Oil Rail Adapters: Both brass adapters use standard 1/4" NPT air hose connection, which allow observation of the High Pressure Oil System's Injector Control Pressure (ICP) by direct gauge connection, and facilitate testing of the High Pressure Oil System for leaks using shop air.
  • IPR Valve Air Test Fitting : This tool has 1/4 inch pipe threads to accept standard air fittings.
  • It takes the place of the IPR valve meaning that the system can be completely sealed so that even the smallest leaks can be detected.
  • 6.0 IPR Valve Socket with Seal Kit: Use with 3/8" square drive, 12 point design socket can tightly locate your IPR valve in a very tight location, also built to bottom out on the hex so it does not put torque on the connector in case it can be reused (Include IPR Valve Seal Kit OE Number 3C3Z9H529A, AP0035).
Check Stock

Moen UT3611ORB Voss Collection M-CORE 3-Series 2-Handle Shower Trim with Integrated Transfer, Valve Required, Oil-Rubbed Bronze

  • UNIQUE FINISH: Oil-Rubbed Bronze finish delivers a rich, dark brown, Old World finish with striking light and dark accents.
  • VALVE REQUIRED: This trim kit requires M-CORE Mixing Valve with Integrated Transfer Valve U232 or U362, with preferred installation option, to complete installation.
  • FOR USE WITH TWO OR THREE SHOWERING DEVICES: Integrated M-CORE Transfer Valves can control 2 or 3 showering devices, a simple transfer cartridge modification changes the valve’s flow from two outlets to three outlets.
  • IMPORTANT: When using 3 Showering Devices, transfer valve cartridge must be modified. Simple Cartridge Modification changes the valves flow from two outlets to three outlets. See Transfer Valve Instructions for additional information..
  • IMPORTANT: When using 2 Showering Devices, designated outlet 3 must be CAPPED. Caps sold separately..
  • PRESSURE-BALANCING CAPABILITY: M-CORE valves, with 3-Series trim, have pressure-balancing capabilities designed to control temperature fluctuations in the event of water pressure changes in the home.
  • VOLUME CONTROL: Features volume control, allowing you to adjust the flow of water for greater functionality.
Check Stock

Lubeworks Oil Control Valve Meter Nozzle Preset Digital 10 Gpm / 35 Lpm Heavy Duty Air Operated Pneumatic 1/2\ Inch Npt Inlet Pressure Range 7-1000 Psi / 0.5-70 Bar Flexible Spout (Not for Gas)

  • VALVE SPECS - This Lubeworks Preset Digital Control Valve has a Max Flow rate of 10GPM / 35LPM, at a precision of ±0.5%, handling Viscosity of 8-5000mPas, a Max Pressure Range of 7Mpa 0.5-50BAR / 7-1000PSI.
  • An Inlet Connection of 1/2" inch Npt Female connecting to industry-standard oil hose reels.
  • battery-powered w/ 1x Alkaline Cell 9v Battery, altogether weighing 3.3 lbs, including the Digital Preset LCD Meter and Flexible Spout.
  • EFFICIENT and SUPERIOR - This Preset LCD Digital Meter Control Valve has a 4-digit easy to read screen, low battery indicator to avoid sudden shut-off, can measure/dispense in various calibrations of Liters, Gallons, Pints, and Quarts.
  • Made of an aluminum frame, exterior ergonomic oil/waterproof polypropylene shell and shockproof rubber, to ensure strength/durability.
  • Our compact design has zero back pressure capability, delivering consistent measurements and smooth dispensing during operation.
  • SAFETY and PROPER USE - Our Control Valves include rubber protection to absorb shock or an impact-resistant polypropylene body, both delivering prolonged lifetime in workshops.
  • Lubeworks Control Valves are only suitable for: oils, motor oils, synthetic hydraulic oil, gear oil and transmission fluids.
Check Stock

Chief G Series P80 Hydraulic Directional Control Valves - Hydraulic Speed Control Valve - 3 Spool, 21 GPM, 4 Way 3 Pos Spring Center, SAE 10 Inlet and Work Ports, SAE 12 Outlet Ports, 3625 PSI

  • Durable - The hydraulic directional control valve is a cast-iron structure, which can be used for a long time.
  • 5 Spool Hydraulic Valve - The hydraulic valve can manage and guide the flow of hydraulic oil between hydraulic pumps and hydraulic cylinders, motors, tanks, and more.
  • Double Acting - This control valve comes with 5 spools and SAE O-ring in/out ports. All spools are standard double-acting spools, which are very suitable for double-acting cylinders.
  • High Efficiency - The relief valve range is up to 3600 PSI and the maximum flow is up to 13 GPM.
  • Widely Used - The hydraulic directional control valve is very suitable for small tractors, tractor loaders, fellers, forklift environmental vehicles, light loaders, log splitters, and more.
Check Stock

YSTOOL 10L Pneumatic Fluid Extractor Dispenser Set ATF Refill Tool Kit for Changing Oil in Engine Transmission Differential Transfer Case Gear Gearbox Power Steering Coolant with Pump Assembly Tank

  • ..., Hyundai, Infiniti, VOLVO and Lexus. You can find appropriate models by applicable manual.
  • YSTOOL pneumatic oil change tool set allows two-way operation of oil suction and refueling, quick and sparkless. Absorb, transport and distribute liquids under safe and clean conditions. The consistent conversion of the 2-way control valves (blue screw valve and air inlet ball valve) on the pump assembly to achieve the conversion between extracting and dispensing, very easy. Pneumatic tool, works with vacuum pump to extract and with air pump to refill, ensuring high efficient and labor-saving.
  • Pump assembly incorporates the container cover, the handle trigger with lock, 2-way control valves for conversing evacuate and dispense, safety valve for automatically releasing excessed pressure (above 43psi /3bar), 1/4" American style air inlet plug, pressure gauge (0-80psi/0-6bar) for monitoring the pressure change, quick coupler for connecting main hose. 10L big capacity well constructed container, is marked with accurate scale to help observe the amount of liquid. Stable base avoids dumping.
  • The main hose is 80" long, with a quick plug on one side to connect the container, and a quick coupler on the other side to connect the dipstick tubes or ATF adapters. There is a b....
Check Stock

Injector Pressure Regulator Valve - IPR Valve - Compatible with Ford Trucks - Powerstroke 6.0L Diesel - E-350, Excursion, F-250, F-350 Super Duty - Replaces 5C3Z9C968CA, CM-5126, 5C3Z-9C968CA, AP63417

  • Replacement Injector Pressure Regulator Valve - regulates the oil bypass circuit of the high pressure oil pump. It is an electromagnetic valve that opens and closes to allow high pressure oil into the injectors. This enables the PCM to control fuel delivery by increasing the speed in which the IPR valve operates thus, being a critical component in your vehicle system..
  • Compatible Replacement for Ford 6.0L Vehicles - 2005 E350 Club Wagon | 2005 - 2010 E350 Super Duty | 2005 Excursion | 2005, 2006, 2007 F250 Super Duty | 2005, 2006, 2007 F350 Super Duty |. The injector pressure regulator valve can be located after removing the intake and the fuel filter housing above the engine which can be seen attached to the high pressure oil pump (HPOP)..
  • Replaces Part# 5C3Z9C968CA, 1846057C1, CM-5126, 5C3Z-9C968-CA, AP63417 - commonly found on popular F-250, F-350 Super Duty, E-350 and Excursion models with 6.0L V8 Diesel Powerstoke Engines including years 05, 06, 07, 08, 09, 10. If you are experiencing no or hard starting when the engine is hot or after stalling and usually starts when it is cold or your vehicle is idling erratically or jerking then you may have a problem with your IPR valve..
  • OEM Fit, Quality, Finish - While this is not a genuine OEM part, this inj....
Check Stock

Benefast VTEC Solenoid Spool Valve w/Timing Oil Pressure Switch & Gasket Compatible with Honda Accord CR-V Element Civic Acura RSX Acura TSX Replacement# 15810-RAA-A01 15810-RAA-A03

  • The VTEC (Variable Valve Timing and Lift Electronic Control) system increases the amount of intake valve lift for increased power. It accomplishes this by turning a control solenoid 'ON' to allow oil pressure into the VTEC control passages to apply pins that will lock the intake rockers. When the oil pressure is present, the pressure switch signal will go high. When the control solenoid is turned 'OFF', the oil pressure is dumped and the oil pressure switch signal will go low..
  • If the pressure switch signal is not logical for the commanded state of the control solenoid, a DTC will set and the PCM will go into a 'fuel-cut' mode limiting engine rpm and performance. The PCM simply doesn't 'know' what the state of the intake valves are, so you end up with the symptoms you describe..
  • This VTEC Solenoid Fits for the Following Vehicles: Honda Accord 2003-2007, Honda Civic 2002-2005, Honda CR-V 2002-2009, Honda Element 2003-2011, Acura RDX 2002-2012, RSX 2002-2006, Acura TSX 2004 2005 2006 2007 2008..
  • Customers can find the product you need accurately according to the OE number. Replacement part number: 15810-RAA-A01, 15810-RAA-A02, 15810-RAA-A03, 15810-PNE-G01, 917-224, 917224, 15810RAAA01, 15810RAAA03, 15810RAAA02, 15810PNEG01..
Check Stock

Dasbecan Engine Variable Timing Oil Control Valve VVT 12633613 916-806 Compatible with Chevrolet Malibu Impala 2.5L 2014 2015

  • Engine variable timing oil control valve fit for Chevrolet Impala L4 153 2.5L 2457cc 2014-2015, fit for Chevrolet Malibu L4 153 2.5L 2457cc 2014-2015..
  • Replaces#: 12633613, 19419980, 916-806, 918-806, 916806, 918806, 61002771, VVT401, VV1301..
  • Function: Precision machining enables accurate and reliable operation, all items tested for reliability, durability and performance..
  • Durable Material: This Engine variable timing oil control valve has excellent mechanical stability and anti-corrosion performance, long service life and no deformation..
  • No-worried Warranty: If you have any questions about our product, please feel free contact to us directly, we would reply within 24 hrs..
Check Stock

DC 24V 1.5\/Φ38 Port Motorized Butterfly Valve, 304 Stainless Steel Tri Clamp GDAE10 for Food, Pharmaceutical, Beverage, Cosmetics, Sanitary 8W

  • ... good corrosion resistance. They are specially designed for long service life. There is a silicone ring inside to ensure the tightness so that the liquid is not easy to leak..
  • 【HASSLE-FREE OPERATION】 - Convenient operation allows you rapid opening and closing, only to rotate 90° from fully open to fully closed. Control mode: single-acting, automatic return, You can perform local control and remote control, saving human resources and time to a large extent..
  • 【ACCURATE PRODUCT PARAMETER】 - The outer diameter of the sanitary pneumatic valve is 2 in / 51 mm, the size of the ferrule is 2.5 in / 64 mm. Our butterfly valve adopts a disc-shaped butterfly plate, which can better control the flow of liquid..
  • 【EXCELLENT & STABLE PERFORMANCE】 - Applicable temperature: ≤176 °F.
  • Environment temperature: 14 °F to 176 °F.
  • Sterilization temperature can reach to 392 °F. Air supply pressure: 5bar-8bar. Maximum pressure 1.6Mp. Our pneumatic butterfly valve is more adaptable than other models on the market..
  • 【APPLICABLE MEDIUM】 - Our tri-clamp butterfly valve is simple in structure, compact in body, light in weight, and made into a large diameter. Applicable media: water, oil, air.
  • widely used in food, pharmacy, beer beverage, biological engineering, m....
Check Stock

Carbon Steel Mini Needle Valve - with Round Knob 1/4\ NPT 6000 PSI DAIRAZAN

  • ...sion resistance, ductility at high temperatures, and low magnetic permeability. It is nickel plated so that it is anti-rust and corrosion resistant..
  • 【High Quality】High pressure brass needle valve, stable smooth delicate tightness practical. The brass needle valve is clean and bright inside, and the ruler can be controlled accurately. Its exquisite processing, can withstand greater pressure than other types of valves, strong connection, high pressure resistance, good sealing performance and repeatable installation..
  • 【Easy to Use】The product is easy to install and maintain, and it is safe and reliable to work. If you need a long time and stable control, it is best to use it with a regulator..
  • 【Widely Applications】Needle valve is an important part of the instrument measurement pipeline system, used to adjust the flow to the instrument or other industrial applications, open or cut off the pipeline path. Generally used in water, steam, gas, oil and other media with smaller flow and higher pressure. It is often used in industrial automatic control piping systems such as ships, oil refining, chemical, electric power, medicine, and food..
Check Stock

CROSS Manufacturing SBAF2J 143430 SBA Series Cast Iron Double Spool Monoblock Hydraulic Directional Control Valve with joystick, 1st Spool 4-Position Float, 2nd Spool 3-Position, Open Centered, 3/4\ x 3/4\ x 1/2\ NPT Female, 2500 psi, Grey

  • Durable - The hydraulic directional control valve is a cast-iron structure, which can be used for a long time.
  • 2 Spools Hydraulic Valve - The hydraulic valve can manage and guide the flow of hydraulic oil between hydraulic pumps and hydraulic cylinders, motors, tanks, and more.
  • Double Acting - This control valve comes with 2 spools and #8 SAE O-ring in/out ports. All spools are standard double-acting spools, which are very suitable for double-acting cylinders.
  • Widely Used - The hydraulic directional control valve is very suitable for small tractors, tractor loaders, fellers, forklift environmental vehicles, light loaders, and more.
  • Max Pressure: 3600 PSI, Inlet Port: SAE 10, Outlet Port: SAE 12, Working Ports: SAE 10, Fluid Temperature: 5 to 176℉, Valve Type: 4 way 3 positions, Mounting: 3 bolts m8 needed.
Check Stock

ONER Driver Side Valve Cover with Gasket & Bolts Compatible with 1999-2008 Cadillac Escalade, Chevy Silverado, Suburban, Tahoe, Trailblazer, GMC Sierra, Yukon，Replace# 12570427 264-965

  • ...Quality Aluminum Material And High-Quality Sealing Rubber，Designed And Manufactured According To OEM， And The VALVE COVER Are Tested Before Leaving The Factory To Ensure That The Product Quality Meets The Standards.The Price Is Only A Small Part Of The Dealer!.
  • 【After-Sales Service】- Establish Strict Quality Control Standards, 1 Year Warranty, Worry-free Return And Refund Policy, Buy With Confidence!If You Have Any Questions About Valve Cover, Please Contact Us, We Will Help You Deal With It As Soon As Possible！.
Check Stock