Top Signal Input Module

Large Current 50A H-Bridge High-Power Single-Channel Motor Driver Module Semiconductor Refrigeration

  • 【H-bridge Driver Module】The drive uses a full H-bridge driver module full-bridge MOSFET driver chip and composed with very low internal resistance and high current. MOSFET H-bridge driver circuit, with strong drive and braking effect, signal isolation chip isolates motor drive effectively..
  • 【Effective Protection】With the microcontroller PWM signal isolation, effectively protect microcontroller..
  • 【Input Maximum】To achieve the motor forward and reverse rotation, two PWM input maximum 200kHz frequency..
  • 【Fully Compatible】Power indicator is schematically clear. The power supply voltage 5V to 15V. 3.3V to 12V, PWM level is fully compatible. High current 50A..
  • 【Warm Tips】Ffor your safety and protection of use, our product is tested to ensure trouble-free installation and performance, please rest assured to buy..
Check Stock

DORHEA 5PCS TM1637 0.56\ 4 Bits Digital LED Display Module with Clock Display 0.36 inch Common Anode Red Digital Tube Board with Cable for Arduino Raspberry Pi DIY Kits

  • The module is a 12 foot with a clock point four common anode tube (0.36 in.) display module driver IC is TM1637 driver IC TM1637, only two signal lines can make the MCU control 4 8 digital tube..
  • Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable. Control interface level can be 5V or 3.3V..
  • 4-digit LED display module with LED brightness adjustable and clock point, can be used to display decimal, letters and so on, suitable for uses in induction cooker, micro-wave oven and small household electrical appliance..
  • Total 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
  • The Positioning holes in this LED Display Module 4 Bits has 4 M2 screws positioning hole diameter is 2.2mm and the positioning of the module is easy to install with easy to achieve the inter-module combination..
Check Stock

Sabaj Audio PHA2 Portable Headphone Amplifier Black Color

  • Build-in sabaj-patented boosting power module which increase input power from 5V to +-15V..
  • Audiophile-Quality sound with good CNC aluminium cabinet.
  • 5V power input by Micro USB or power adaptor.
  • WIMA&SIEMENS capacitor used,Using TPA6120A2 headphone amplifier chips from TI.
  • RCA analog signal input for amplifier or active speaker connection.
Check Stock

Kuuleyn Frequency to Voltage Converter Module,1-3KHZ 0-10V PWM Signal to Voltage Converter Module Digital Analog Board

  • This module is easy to wire and convenient to use.
  • PWM converts digital signals into analog signal (0 to 10V).
  • Input digital signal can be 5V or 24V level 0-100% PWM signal.
  • Output analog signal can be 0-10v voltage or 0-5v voltage.
  • Can be used for industrial control panel PLC or other signal interface switching.
Check Stock

3v Relay Board Raspberry Pi Arduino Relay Module 1 Channel Opto-Isolate High Level Trigger for IOT ESP8266 Microcontrollers Development Board

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Main Specification】- The 3v Relay 1 Channel power switch module compatible with 10A 250VAC and 10A 30VDC load.4pcs * 2.5 mm Fixed Bolt Hole..
  • 【Adopted Optocoupler Isolation】- 3V/3.3V power relay module supports photocoupler isolation control and dual power supply input ensure high anti-interference ability. Fast response time less than 20ms and long life time up to 100,000 times snap action with diode freewheel protection..
  • 【Jumper Caps】You can select whether the relay and the signal use the same power supply or not by removing the jumper caps on the pins. And It is better to share the same power supply, because that is more convenient for using..
  • 【Wide Application】- These 3v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/IOT/ ESP8266 module etc..
Check Stock

100dB Logarithmic Amplifier Module Dynamic Range Detection with Limiting Output for FSK PSK Demodulation 5MHZ‑500MHZ

  • WORKING PRINCIPLE - Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
  • STABLE AND ACCURATE - ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • WIDELY USED - Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • WITH LIMITING OUTPUT - AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation..
  • PARAMETER RANGE - 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain..
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

0-10V Signal Isolation Module, S-10V10V Analog Quantities Voltage Signal Isolation Module for PLC/MCU Isolating High Voltage or Current (Voltage) Signals

  • ➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
  • ➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
  • ➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
  • ➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
  • ➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..
Check Stock

Tangyy 5pcs HC-SR04 Ultrasonic Sensor, Distance Sensor with Ultrasonic Transmitter and Receiver Module fit for Raspberry Pi,MEGA2560, Robot (Blue)

  • Widely used: Sweepers, DIY robot cars, for raspberry pi project,It can be building a little robot to measure distances in a room under construction.
  • HC-SR04 Ultrasonic Sensor Module: It measures distance by sending out a sound wave at a specific frequency and receiving back that sound wave to bounce.
  • Good Accuracy: Power Supply :3V-5.5V DC, Detection angle: 003c15 °, Minimum target distance is 2.0cm from the end of the Voltage transducers. Maximum repeatable target distance is 2CM-150CM for a large unobstructed stationary target.
  • Easy to install: There are 4 pins out of the module, VCC supply 5V, and GND is ground wire. TRIG is trigger control signal input, ECHO is echo signal output, So it's a very easy interface for controller to use it ranging.
  • Note: The module should be inserted in the circuit before been powered to avoid producing high level of Mis-operation.
Check Stock

1pcs 1-Bit AC 220V Optocoupler Isolation Module

  • Output TTL level can be detected with the microcontroller. The power supply can be 3-5V.
  • the PLC input terminal of the PLC COM power supply 24V input termination of the board signal output OUT, optocoupler board GND power negative.
  • When the power module in the power of the board after the white wire frame can not touch any device .. because it is high voltage. Note the safety of electricity.
Check Stock

GSM Alarm, 3G GSM 8 Channels Mini Alarm Intruder, SMS Alarm Smart Home Security System, Remote Alarm System(US)

  • ☆☆Built‑in 3G module, compatible with GSM version. The input port can be selected as NC or NO alarm mode. Use easily and conveniently, it can be easily embedded into other equipment, as a remote alarm system..
  • ☆☆The input of GA09‑B is a switch signal. When the input port is short‑circuited with the ground (GND), GA09‑B will send an alarm message to the preset alarm phone, or call the set alarm number. The content of the alarm message can be set by yourself..
  • ☆☆Up to 6 groups of called numbers can be set. When the alarm input has a trigger signal, an alarm message will be sent to the alarm number, or you can call the alarm directly..
  • ☆☆We have professional customized APP, support for iOS/Android system, you can simply send messages through APP to set up. The wide voltage of this GSM alarm box is DC5 to 15V DC for power supply..
  • ☆☆Widely used, includes home security, warehouses, remote computer rooms, industrial monitoring sites, security protection, home security and other unattended points..
Check Stock

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..
Check Stock