Top Welding Cable Connector Joint

EBOOT 20 AWG JST Plug Connector 2 Pin Male Female Plug Connector Cable Wire for LED Lamp Strip RC Toys Battery, 10 Pairs

  • Total cable length: approx. 210 mm/ 8.3 inch.
  • 2 Pin JST connector, one side for plug the other side for welding.
  • Package including: 10 pairs JST plug connector with cable wire (10 pieces female, 10 pieces male).
  • This JST plug connector is suitable for most mini RC helicopter, LED strip light and good for connecting motor, ESC battery.
Check Stock

WeldingCity 3-pk Dinse-Type Twist-Lock Insulated Connector Pair (Male/Female) for Welding Cable AWG #2-1/0 (35-50mm) | Pack of 3 Pairs

  • 4 pairs of premium Dinse-type cable connector pair (male/female) for use with welding cable connection in welders from Lincoln, Miller, ESAB, etc..
  • Male connector is with Dinse-type pin of .355" diameter (25-mm small) and pi of 1/2" diameter (35-50mm, 50-70mm and 70-95mm)..
  • Compatible with Dinse-type twistlock connectors in mainstream welders ( Miller, Lincoln, ESAB, etc.). Available connector sizes 16-25mm (small 0.355" pin, #4-#3), 35-50mm (1/2" pin, #2-1/0), 50-70mm (1/2" pin, 2/0-3/0) and 70-95mm (1/2" pin, 3/0-4/0)..
  • All connectors/adapters are equipped with heat and oil resistant covers as well as cable connection screws and copper splice caps. 3-pair per package..
  • U.S. based welding and hardware supplier. Strong technical support with experienced customer service to address buyer's any question..
Check Stock

KINGQ Welding Cable Joint Quick Connector Pair DINSE-Style 100Amp-200Amp (#6-#4) 16-25 SQ-MM 2-set

  • Premium Dinse-type insulated cable connector pair (male/female) and female terminal adapter (threaded stud to Dinse male connector) for use with welding cable connection in welders from Lincoln, Miller, ESAB, etc..
  • Insulated Dinse-type male connector is with .355" pin diameter (25-series) and 1/2" pin diameter (35/50/70-series). 45° angle terminal adapter with 17/32" stud hole and female acceptor for 1/2"-pin male plug..
  • Compatible with Miller 25-70 series Dinse twistlock connectors/adapters and fit other mainstream welders (Lincoln, ESAB, etc.) with Dinse connection: Miller 25-series (small 25-mm, #4-#3, P/N 127836/127835).
  • 50-series (35-50mm, #2-1/0, P/N 129527/129526).
  • 70-series (50-70mm, 1/0-3/0, P/N 134460/136600). Female terminal adapter is compatible with Miller 232728 (50/70-series, 1/2"-pin)..
  • All connectors/adapters are equipped with heat and oil resistant covers as well as cable connection screws and copper splice caps..
  • U.S. based welding and hardware supplier. Strong technical support with experienced customer service to address buyer's any question..
Check Stock

RIVERWELD TIG Welding Cable Panel Connector-plug and Socket Dinse Dinze Quick Fitting 315Amp (2, DKJ35-50)

  • Cable Panel Connector /Euro Style Cable Connector-plug Fit all TIG Welding and Plasma Cutter Machine.
  • 1pcs DKJ35-50 Connector with Black Color..
Check Stock

9TRADING Replacement Mig Welding Gun Stinger Torch Lead 4 Clarke 130EN 180EN Welder Parts

  • The gun is 10 ft long, and will handle .023", .030", and .035" steel, stainless steel, and flux cored wires..
  • There is a gas valve in the handle, so this gun can be used with or without gas..
  • The gas hose extends 6 ft beyond the end of the gun, the trigger wires have the correct connector for the 130EN and 180EN welders, and the cable which carries the welding current extends 20" past the end of the gun..
  • You can see the gas hose, trigger connector, and the welding current cable in the second picture..
  • This gun uses the same Clarke contact tips, gas nozzles, and gas diffusers..
Check Stock

iPhone Fast Charger, [Apple MFi Certified] 20W PD USB C Wall Charger Block Plug with 10FT Extra Long Type C to Lightning Fast Charging Data Sync Cable for iPhone 13 12 11 XS XR X 8 iPad and More

  • 【MFi Certified Lightning Cable 】: Each cable contains an authorization chip issued by iPhone to ensure 100% compatibility with iPhone, iPad, iPod.Built with original C48 terminal and smart chip. Original 8 Pin connector with a lightning end, ensured safe charging for your iPhone devices. Enjoy fast data transfer, syncing and charging..
  • 【Ultra High Quality Assurance】 : Reinforced iPhone charger cable with special SR joint design that have passed 40000+ times bending tests for extra protection and durability. Upgraded 3D aluminum connector and exclusive laser welding technology, which to ensure the metal part won't break and also have a tighter connection which fits well even with a protective case on and will never loose connection..
  • 【Perfect 10FT】 : With the 10ft length, you can lie on the couch or sofa and use your devices while you are charging at the same time. And you can use freely in your bedroom, office and even in the backseat of your car..
  • 【MFi certification】 : Ensures complete high speed charge and sync compatibility with iPhone 13/12/11 / 11Pro / 11Max / X / XS / XS Max / XR / 8 / 8 Plus / 7 / 7 Plus / 6s / 6s Plus / 6 / 6 Plus / SE / 5S / 5C / 5, iPad Pro, iPad, iPad mini 4 / 3 / 2, iPad mini, iPad Air 2, iPad Air..
Check Stock

ABN L5-50R Connector – 50 Amp Twist Lock Inlet Locking Power Cord Connector Locking Power Inlet Plug 50A 125/250V

  • CONNECT YOUR CABLE: Use your generator, transfer switch, welding equipment, trailer, RV camper power inlet with this ABN Inlet Locking Connector.
  • KEEP OUT PESTS: Replace your power cord with this twist lock connector so the cord can be removed and stored without leaving an opening that mice or....
  • SECURELY HOLD CABLE: This connector comes with strain reliefs that mount inside the base of the connector to hold the cable (clamp for the cord).
  • PERFECT SIZE: Approximate measurement across the face is 2 inches (5.1cm).
  • Across the back where the cord enters adds 0.25 inch (2.25 inches / 5.7cm....
  • Remove housing by loosening face screws and slide over cable (If a weather-resistant boot is used, slide this over....
Check Stock

150 Amp Welding Electrode Holder Lead Assembly - Dinse 10-25 Connector - #4 AWG cable (15 FEET)

  • Heavy Duty Welding Lead Assembly manufactured with Made in USA Flex-A-Prene highly flexible cable. Cable Size: #4 AWG - 0.343" O.D..
  • Electrode Holder compatible with AF-3. Constructed with Heavy Duty Nylon body. High conductivity jaws and cable connectors. High strength coiled spring for a maximum grip of the electrode. Holds Electrodes up to 1/4"..
  • Dinse 10-25 Cable Connector. ***Please check connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits***.
  • RATED: 150 AMP @ 60% Duty Cycle. ***Please Check you welder´s maximum amperage and look for a cable assembly that matches or exceeds that amperage rating***.
  • Choose the Cable Length from the Menu. These leads are assembled to customer specifications the same day the order is received, they are packed and shipped on a cardboard box or a white USPS Flat Rate Package. You will receive a ready to use fully assembled lead, no tools required..
Check Stock

150 Amp Welding Ground Clamp Lead Assembly - Dinse 10-25 Connector - #4 AWG cable (15 FEET)

  • Heavy Duty Welding Lead Assembly manufactured with Made in USA Flex-A-Prene highly flexible cable. Cable Size: #4 AWG - 0.343" O.D..
  • Ground Clamp compatible with EG-300. Constructed in Zinc-Plated Steel. Large hex screw cable connection assures a tight and safe cable connection. It has a large contact area for an effective ground connection. Its design eliminates arc blowing and facilitates fast grounding spot changing.
  • Dinse 10-25 Cable Connector. ***Please check connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits***.
  • RATED: 150 AMP @ 60% Duty Cycle. ***Please Check you welder´s maximum amperage and look for a cable assembly that matches or exceeds that amperage rating***.
  • Choose the Cable Length from the Menu. These leads are assembled to customer specifications the same day the order is received, they are packed and shipped on a cardboard box or a white USPS Flat Rate Package. You will receive a ready to use fully assembled lead, no tools required..
Check Stock

ESPEEDER 3.0 Lap Joint Band Clamp Exhaust Clamps Pipe Repair Parts Stainless Steel

  • Universal fitment, Joins 3.0" OD Pipe to 3.0" ID Pipe, made of 304 stainless steel. There are 5 sizes for choose, it can meet your various needs.....
  • The lap joint clamps 3.0" are best when cosmetic appearance is important, and have a wide range used. This would include exhaust tips, mufflers, cat....
  • Conforms to pipe and flex tubing, exhaust pipe connector come with an "I" block provides a full 360 °equal distribution of stretching forces, without....
  • No welding design makes lap joint clamp fast, easy and accurate installation. It is removable and reusable. just need to put one of the nut bar on one....
  • SYKRSS value your shopping experience, If you encounter any problems in installing the 3.0" lap joint band clamp, you can feel free to contact us via....
Check Stock

200 Amp Welding Electrode Holder Lead Assembly - Dinse 10-25 Connector - #2 AWG cable (15 FEET)

  • Heavy Duty Welding Lead Assembly manufactured with Made in USA Flex-A-Prene highly flexible cable. Cable Size: #2 AWG - 0.418" O.D..
  • Electrode Holder compatible with AF-3. Constructed with Heavy Duty Nylon body. High conductivity jaws and cable connectors. High strength coiled spring for a maximum grip of the electrode. Holds Electrodes up to 1/4"..
  • Cable Connector Options: LC-40 (Cam-Lock), Dinse 10-25, Dinse 35-70 or Terminal Lug. ***Please select your option from the menu, check the connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits***.
  • RATED: 200 AMP @ 60% Duty Cycle. ***Please Check you welder´s maximum amperage and look for a cable assembly that matches or exceeds that amperage rating***.
  • Choose the Cable Length from the Menu. These leads are assembled to customer specifications the same day the order is received, they are packed and shipped on a cardboard box or a white USPS Flat Rate Package. You will receive a ready to use fully assembled lead, no tools required..
Check Stock

200 Amp Welding Ground Clamp Lead Assembly - Dinse 10-25 Connector - #2 AWG cable (15 FEET)

  • Heavy Duty Welding Lead Assembly manufactured with Made in USA Flex-A-Prene highly flexible cable. Cable Size: #2 AWG - 0.418" O.D..
  • Ground Clamp compatible with EG-300. Constructed in Zinc-Plated Steel. Large hex screw cable connection assures a tight and safe cable connection. It has a large contact area for an effective ground connection. Its design eliminates arc blowing and facilitates fast grounding spot changing.
  • Cable Connector Options: LC-40 (Cam-Lock), Dinse 10-25, Dinse 35-70 or Terminal Lug. ***Please select your option from the menu, check the connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits***.
  • RATED: 200 AMP @ 60% Duty Cycle. ***Please Check you welder´s maximum amperage and look for a cable assembly that matches or exceeds that amperage rating***.
  • Choose the Cable Length from the Menu. These leads are assembled to customer specifications the same day the order is received, they are packed and shipped on a cardboard box or a white USPS Flat Rate Package. You will receive a ready to use fully assembled lead, no tools required..
Check Stock