Top Servo To I2c Board

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino

  • The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
  • A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
  • On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
  • If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
  • Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

Clock Splitter, Electronic Component Stable for Home for Industry

  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
Check Stock

SparkFun Qwiic Single Relay-Up to 5.5A at 240VAC Multiple I2C addresses Available Turn on/Off high Power Device from Low Power microcontroller No Soldering Large Power Loads w/Simple I2C Commands

  • Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino compatible board or another low powered microcontroller? No soldering needed to get started. Plug and play. Code available. Small footprint..
  • The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!.
  • The Qwiic Relay comes with a default I2C address of 0x18 but can be changed with a simple command allowing you to control over 100 Qwiic Relays on a single bus (but please be aware that toggling lots of relays on a 3.3V bus can cause voltage spikes so an external power supply will be required)!.
  • In addition, there is an address jumper on the back of the board. Closing this jumper with solder will change the address to 0x19..
  • Operating Voltage: 1.7V-3.6V. Coil Resistance: 23.5Ω. I2C Address: 0x18 (Default), (Jumper changes to 0x19). Max Current (Through Relay): 5.5A (240 VAC).
Check Stock

Electronic Component, High Clock Splitter Practical for Home for Industry

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

15 Pieces Servo Extension Cables Servo Extension Male to Female RC Servo Extension Cord Wire Cable Compatible with RC JR Futaba RC Car Airplanes (3.9 Inch,5.9 Inch,11.8 Inch,19.7 Inch,23.6 Inch)

  • Wide application: these servo extension s are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
  • Appropriate sizes: the servo extension cord measures approx. 3.9 Inch, 5.9 Inch, 11.8 Inch, 19.7 Inch, 23.6 Inch in length, different size for your use, the color is black and red.
  • Package includes: this package includes 15 pieces of male to female servo extension cables, enough quantity for you to use and replacement, providing more convenience for you.
  • Feature: this male to female servo extension cord featured with female connector on one side, and male connector on the other side, can be connected to the receiving set and steering engine.
  • Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control, which is male to female.
Check Stock

Clock Splitter, Convenient Good Performance Electronic Component for Home for Industry

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield Compatible with Arduino R3 Mega2560

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each..
  • I2C Address: 0x27 or 0x3F.Compatible with Arduino R3/2560 board. http://wiki.sunfounder.cc/index.php?title=I2C_LCD2004.
  • Professonal Support: SunFounder customer service team are always willing to solve any question from our customers .Any problem, please contact us on Amazon..
Check Stock

SunFounder 2004 20x4 LCD Module IIC I2C Interface Adapter Blue Backlight Compatible with MEGA2560 Arduino R3 Raspberry (2 Pack)

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each. (2 Pack).
  • Compatible with Arduino R3/Mega2560 board..
Check Stock

Clock Splitter, Good Performance High Practical Electronic Component for Industry for Home

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

SunFounder Raspberry Pi Pico Starter Kit with 40 Projects Online Tutorials, MicroPython C Piper Make Code, One-Stop Learning Electronics and Programming for Raspberry Pi Arduino Beginners & Experts

  • 【Raspberry Pi Pico Starter Kit】SunFounder Raspberry Pi Pico Basic Starter Kit is One-Stop-Shop for Raspberry Pi Arduino Beginners & Experts. Online tutorials provide you with step-by-step guidance, with 283 items and 40 projects..
  • 【Pre-soldered Raspberry Pi Pico Included】The Raspberry Pi Pico is a high-performance microcontroller board with flexible digital that features the RP2040 with a dual-core ARM Cortex-M0+ processor..
  • 【280+ Items】In addition to Raspberry Pi Pico, it comes with various components, such as: I2C LCD, WS2812 RGB LED Strip, Servo Motor, and PIR Motion Sensor etc. Detailed explanations and learning information are provided for each component..
  • 【Provided 40 Projects】The pico kit includes 40 professional projects in a variety of degrees of complexity. Each lesson includes a circuit diagram, explanation of the operating principle, and an example code..
  • 【3 Programming Languages】MicroPython (18 projects), an officially recommended programming language. C/C++ (13 projects), compatible with the Arduino IDE. Piper Make (9 projects), a simplified version of Scratch, which is ideal for beginners..
Check Stock